Journal of Energy Resources Technology: Recent submissions
Now showing items 1641-1660 of 3450
-
Recommendations for Energy Water Nexus Problems
(The American Society of Mechanical Engineers (ASME), 2014)The chronic water problems in parts of India are probably due mainly to mismanagement. The rolling blackout and brownout problems in the larger Indian cities are due to lack of generation capacity. Since about ninety percent ... -
Special Issue: Recent Studies of Petroleum Wells and Reservoirs
(The American Society of Mechanical Engineers (ASME), 2014) -
Analytical Model to Characterize “Smear Effect†Observed While Drilling With Casing1
(The American Society of Mechanical Engineers (ASME), 2014)The “Smear Effect†observed during a casingwhiledrilling operation helps reduce lost circulation, provides wellbore strengthening, and improves the fracture gradient so we can drill more effectively through depleted ... -
Semi Analytical Proxy for Vapex Process Modeling in Heterogeneous Reservoirs
(The American Society of Mechanical Engineers (ASME), 2014)Vapex (vapor extraction) is a nonthermal process that has significant potential in providing a more environmentally friendly and energyefficient alternative to steam injection. Vaporized solvent injected insitu dissolves ... -
Experimental Study of Sand Particle Concentration Profiles in Straight and Pipe Elbow for Horizontal Multiphase Flows
(The American Society of Mechanical Engineers (ASME), 2014)Sand production is one of the major concerns for oil and gas producers. If production fluid velocities are not controlled properly, the produced sand may erode the pipelines which may result in pipe failures and halt the ... -
Transient Simulation of Wellbore Pressure and Temperature During Gas Well Testing
(The American Society of Mechanical Engineers (ASME), 2014)An abnormal phenomenon may occur during gaswell testing: the wellhead pressure initially rises and then drops when shuttingin a well; the wellhead pressure initially drops and then rises when opening a well. To determine ... -
Interpretation of Hydraulic Fracturing Pressure in Tight Gas Formations1
(The American Society of Mechanical Engineers (ASME), 2014)The interpretation of hydraulic fracturing pressure was initiated by Nolte and Smith in the 1980s. An accurate interpretation of hydraulic fracturing pressures is critical to understand and improve the fracture treatment ... -
Laminar Flame Characteristics of Partially Premixed Prevaporized Palm Methyl Ester and Diesel Flames
(The American Society of Mechanical Engineers (ASME), 2014)Palm methyl ester (PME) is a renewable biofuel that is produced by the transesterification of palm oil and is a popular alternative fuel used in the transportation sector, particularly in Asia. The objective of this ... -
Comparison of Models Correlating Cumulative Oil Production and Water Cut
(The American Society of Mechanical Engineers (ASME), 2014)There have been many models to estimate reserves and predict oil production performance using the relationship between water cut, fw, (or wateroil ratio, WOR) and cumulative oil production (Np) in the literature. However, ... -
Real Time Analysis of Engine Power, Thermal Efficiency, and Emission Characteristics Using Refined and Transesterified Waste Vegetable Oil
(The American Society of Mechanical Engineers (ASME), 2014)The study aims to investigate the realtime engine performance in terms of brake power, thermal efficiency and emission characteristics of a diesel engine. Waste vegetable oil samples were collected from several sources, ... -
Constrained Equilibrium Modeling of Methane Oxidation in Air
(The American Society of Mechanical Engineers (ASME), 2014)Ratecontrolled constrainedequilibrium method has been further developed to model methane/air combustion. A set of constraints has been identified to predict the nonequilibrium evolution of the combustion process. The set ... -
An Experimental and Modeling Study Into Using Normal and Isocetane Fuel Blends as a Surrogate for a Hydroprocessed Renewable Diesel Fuel
(The American Society of Mechanical Engineers (ASME), 2014)A new hydroprocessed renewable diesel (HRD) fuel comprised both straight chain and branched alkane fuel components. In an effort to find a research surrogate for this fuel, single cylinder engine testing was performed with ... -
Infiltration Velocity and Thickness of Flowing Slag Film on Porous Refractory of Slagging Gasifiers
(The American Society of Mechanical Engineers (ASME), 2014)Two analytical formulations that describe the fluid interactions of slag with the porous refractory linings of gasification reactors have been derived. The first formulation considers the infiltration velocity of molten ... -
Experimental Study of Solar Powered Desalination Pond as Second Stage in Proposed Zero Discharge Desalination Process
(The American Society of Mechanical Engineers (ASME), 2014)An experimental scale desalination pond which utilizes solar energy as a heat source is studied in this paper. The marked solar desalination pond is considered as one of the main stages in a proposed zero discharge ... -
Invariant Forms of Conservation Equations and Some Examples of Their Exact Solutions
(The American Society of Mechanical Engineers (ASME), 2014)A scaleinvariant model of statistical mechanics is described leading to invariant Boltzmann equation and the corresponding invariant Enskog equation of change. A modified form of Cauchy stress tensor for fluid is presented ... -
Comparing Energy and Cost Optimization in Distributed Energy Systems Management
(The American Society of Mechanical Engineers (ASME), 2014)Distributed generation, despite not being a new concept, is assuming a leading role in the field of energy conversion, as it should contribute to the enhancement of efficiency, flexibility, and reliability of national ... -
Boilers Optimal Control for Maximum Load Change Rate
(The American Society of Mechanical Engineers (ASME), 2014)In many cogeneration systems, one or more boilers are used in hot standby to meet the plant demand of steam in case of failure or upset in the cogeneration unit. Such boilers need to quickly respond to sudden and large ... -
Systematic Optimization of the Design of Steam Cycles Using MINLP and Differential Evolution
(The American Society of Mechanical Engineers (ASME), 2014)The process synthesis and design optimization of energy conversion systems can be modeled as a mixed integer nonlinear programming (MINLP) problem. The nonconvexity potential and the combinatorial nature of the objective ... -
A New Support Vector Machine and Artificial Neural Networks for Prediction of Stuck Pipe in Drilling of Oil Fields
(The American Society of Mechanical Engineers (ASME), 2014)Stuck pipe is known to be influenced by drilling fluid properties and other parameters, such as the characteristics of rock formations. In this paper, we develop a supportvectormachine (SVM) based model to predict stuck ... -
Evaluation of Impact of Shading Devices on Energy Consumption of Buildings in Tropical Regions
(The American Society of Mechanical Engineers (ASME), 2014)The aim of this paper is to demonstrate the role of shading devices in the improvement of energy efficiency of buildings in hot dusty and dry tropical regions. The effect of shading in reducing the energy consumption of ...