Journal of Energy Resources Technology: Recent submissions
Now showing items 1481-1500 of 3450
-
Reduction of Sulfur Dioxide Emissions by Burning Coal Blends
(The American Society of Mechanical Engineers (ASME), 2016)Given that sulfur contents of coals vary widely, this work investigated whether cofiring of highsulfur coals with lowsulfur coals of different ranks has any distinct advantages on lowering the sulfur dioxide emissions of ... -
Integrated Investigation of Dynamic Drainage Volume and Inflow Performance Relationship (Transient IPR) to Optimize Multistage Fractured Horizontal Wells in Tight/Shale Formations
(The American Society of Mechanical Engineers (ASME), 2016)This study presents an integrated approach to evaluate the efficiency of fracturing stimulation and predict well production performance. As the pressure disturbance propagates throughout the reservoir during longtime ... -
An Experimental Study of the Collection of Fog Droplets Using a Mesh Fabric: Possible Application to Cooling Towers
(The American Society of Mechanical Engineers (ASME), 2016)An experimental study is presented of the ability of fine meshes to remove fog drops from an air flow. Specifically, the collection efficiency (CE) was measured for fog drops passing through mesh fabrics. Meshes composed ... -
The Effect of Thermal Treatment of Hematite Ore for Chemical Looping Combustion of Methane
(The American Society of Mechanical Engineers (ASME), 2016)For chemical looping processes to become an economically viable technology, an inexpensive carrier that can endure repeated reduction and oxidation cycles needs to be identified or developed. Unfortunately, the reduction ... -
Effect of Sand Content on the Filter Cake Properties and Removal During Drilling Maximum Reservoir Contact Wells in Sandstone Reservoir
(The American Society of Mechanical Engineers (ASME), 2016)The drilling mud program contains many tests such as filtration rate and filter cake properties to select the proper drilling fluid additives that yield the standard ranges of the viscosity, filtration rate, etc. However, ... -
Preheats Effects on JP8 Reforming Under Volume Distributed Reaction Conditions
(The American Society of Mechanical Engineers (ASME), 2016)Conventional noncatalytic fuel reforming provides low efficiency, large amounts of char and tar and limited control on chemical composition of the syngas produced. The distributed reaction regime can be used to assist ... -
Application of Artificial Neural Network–Particle Swarm Optimization Algorithm for Prediction of Gas Condensate Dew Point Pressure and Comparison With Gaussian Processes Regression–Particle Swarm Optimization Algorithm
(The American Society of Mechanical Engineers (ASME), 2016)For gas condensate reservoirs, as the reservoir pressure drops below the dew point pressure (DPP), a large amount of valuable condensate drops out and remains in the reservoir. Thus, prediction of accurate values for DPP ... -
Investigation of the Predicting Ability of Single Phase Chemical Equilibrium Modeling Applied to Circulating Fluidized Bed Coal Gasification
(The American Society of Mechanical Engineers (ASME), 2016)In this study, a nonstoichiometric singlephase chemical equilibrium model was developed to simulate atmospheric circulating fluidized bed (CFB) coal gasifiers in reference to the available experimental and simulation data. ... -
Long Term Effects of CO2 Sequestration on Rock Mechanical Properties
(The American Society of Mechanical Engineers (ASME), 2016)The longterm geological sequestration of carbon dioxide (CO2) in underground formations (deep saline aquifers) is the most economically viable option to decrease the emissions of this greenhouse gas in the atmosphere. The ... -
Laser Ignition and Flame Speed Measurements in Oxy Methane Mixtures Diluted With CO2
(The American Society of Mechanical Engineers (ASME), 2016)Ignition and flame propagation in methane/O2 mixtures diluted with CO2 are studied. A laser ignition system and dynamic pressure transducer are utilized to ignite the mixture and to record the combustion pressure, respectively. ... -
Estimating the Theoretical Performance Limits of a Biogas Powered Dual Fuel Diesel Engine Using Emulsified Rice Bran Biodiesel as Pilot Fuel
(The American Society of Mechanical Engineers (ASME), 2016)The present study is an attempt to estimate the energy and the exergy potential of a biogas run dual fuel diesel engine using emulsified rice bran biodiesel (RBB) as pilot fuel at varying compression ratio (CR) and injection ... -
Combustion Characteristics of Partially Premixed Prevaporized Palm Methyl Ester and Jet A Fuel Blends
(The American Society of Mechanical Engineers (ASME), 2016)Palm methyl ester (PME) is an attractive alternate biofuel produced by the transesterification of palm oil with methanol. This paper is a sequel to our earlier papers on the comparison of the flame structure and emission ... -
A New MPPT Algorithm for Vehicle Integrated Solar Energy System
(The American Society of Mechanical Engineers (ASME), 2016)Photovoltaic (PV) systems are considered as a support unit and ecofriendly energy source for the electric vehicles. If the surface of the electric vehicle is covered by PV cells, it is possible to store considerable amount ... -
An Eulerian Approach to Computational Fluid Dynamics Simulation of a Chemical Looping Combustion Reactor With Chemical Reactions
(The American Society of Mechanical Engineers (ASME), 2016)Chemicallooping combustion (CLC) is a nextgeneration combustion technology that shows great promise in addressing the need for highefficiency lowcost carbon capture from fossil fueled power plants. Although there have been ... -
The Effects of Fuel Mixtures in Nonpremixed Combustion for a Bluff Body Flame
(The American Society of Mechanical Engineers (ASME), 2016)A numerical investigation is presented assessing the effects of hydrogen compositions and nonflammable diluent mixtures on the combustion and NO emission characteristics of syngas nonpremixed flames for a bluffbody burner. ... -
Estimation of Operating Parameters of a Water–LiBr Vapor Absorption Refrigeration System Through Inverse Analysis
(The American Society of Mechanical Engineers (ASME), 2016)In this paper, an inverse problem is solved for estimating parameters of a steamdriven water–lithium bromide (LiBr) vapor absorption refrigeration system (VARS) using a differential evolution (DE)based inverse approach. ... -
Modeling and Experimental Study of Solid–Liquid Two Phase Pressure Drop in Horizontal Wellbores With Pipe Rotation
(The American Society of Mechanical Engineers (ASME), 2016)Determining pressure loss for cuttingsliquid system is very complicated task since drillstring is usually rotating during drilling operations and cuttings are present inside wells. While pipe rotation is increasing the ... -
Dynamic Measurement of Spatial Attitude at Bottom Rotating Drillstring: Simulation, Experimental, and Field Test
(The American Society of Mechanical Engineers (ASME), 2016)In the oil and gas drilling engineering, measurementwhiledrilling (MWD) system is usually used to provide realtime monitoring of the position and orientation of the bottom hole. Particularly in the rotary steerable drilling ... -
A New High Temperature Gel for Profile Control in Heavy Oil Reservoirs
(The American Society of Mechanical Engineers (ASME), 2016)Controlling the phenomenon of steam channeling is a major challenge in enhancing oil recovery of heavy oil reservoirs developed by steam injection, and the profile control with gel is an effective method to solve this ... -
Sustainable Engineering in the Global Energy Sector
(The American Society of Mechanical Engineers (ASME), 2016)The current age is one in dire need of teaching engineers of all branches about sustainability. The principle is that engineering choices have to be decided in the framework of constraints related to energy and materials ...