Journal of Energy Resources Technology: Recent submissions
Now showing items 1141-1160 of 3450
-
A Proxy Model for Predicting SAGD Production From Reservoirs Containing Shale Barriers
(The American Society of Mechanical Engineers (ASME), 2018)Artificial intelligence (AI) tools are used to explore the influence of shale barriers on steam-assisted gravity drainage (SAGD) production. The data are derived from synthetic SAGD reservoir simulations based on petrophysical ... -
Preparation and Characterization of Chemical Agents for Augmenting Injectivity in Low Permeability Reservoirs
(The American Society of Mechanical Engineers (ASME), 2018)In this paper, experimental techniques have been developed to prepare and characterize chemical agents for augmenting injectivity in low permeability reservoirs. First, chemical agents are selected, formulated, and optimized ... -
Multiple-Relaxation-Time Lattice Boltzmann Simulation of Flow and Heat Transfer in Porous Volumetric Solar Receivers
(The American Society of Mechanical Engineers (ASME), 2018)The flow and heat transfer (FHT) in porous volumetric solar receiver was investigated through a double-distributed thermally coupled multiple-relaxation-time (MRT) lattice Boltzmann model (LBM) in this study. The MRT-LBM ... -
Contrasting the Pyrolysis Behavior of Selected Biomass and the Effect of Lignin
(The American Society of Mechanical Engineers (ASME), 2018)This study was aimed at comparing the pyrolysis behavior of several selected biomass samples, namely, pine wood, poplar wood, wheat straw, and sugarcane bagasse, with a particular attention to the effect of lignin. Raw ... -
A Computational Investigation of Fuel Chemical and Physical Properties Effects on Gasoline Compression Ignition in a Heavy-Duty Diesel Engine
(The American Society of Mechanical Engineers (ASME), 2018)Gasoline compression ignition (GCI) offers the potential to reduce criteria pollutants while achieving high fuel efficiency. This study aims to investigate the fuel chemical and physical properties effects on GCI operation ... -
Analysis of Wellbore Temperature Distribution and Influencing Factors During Drilling Horizontal Wells
(The American Society of Mechanical Engineers (ASME), 2018)Horizontal well drilling technology is widely used in the exploitation of petroleum and natural gas, shale gas, and geothermal resources. The temperature distribution of wellbore and surrounding formation has a significant ... -
Microwave-Assisted Pyrolysis of Biomass for Bio-Oil Production: A Review of the Operation Parameters
(The American Society of Mechanical Engineers (ASME), 2018)As compared with the conventional electrical heating pyrolysis, microwave-assisted pyrolysis (MAP) is more rapid and efficient due to its unique heating mechanisms. However, bio-oil production from MAP of biomass is strongly ... -
Experimental Study of the Pore Structure Characterization in Shale With Different Particle Size
(The American Society of Mechanical Engineers (ASME), 2018)In order to study the effects of particle size on the determination of pore structure in shale, the outcrop of Ordovician Wufeng (WF) and Silurian Longmaxi shale (LMX) samples from Sichuan basin were chosen and crushed ... -
A General Boundary Integral Solution for Fluid Flow Analysis in Reservoirs With Complex Fracture Geometries
(The American Society of Mechanical Engineers (ASME), 2018)Modeling fractured reservoirs, especially those with complex, nonorthogonal fracture network, can prove to be a challenging task. This work proposes a general integral solution applicable to two-dimensional (2D) fluid flow ... -
A New Method of Porous Space Reconstruction Using Multipoint Histogram Technology
(The American Society of Mechanical Engineers (ASME), 2018)Pore-scale modeling is becoming a hot topic in overall reservoir characterization process. It is an important approach for revealing the flow behaviors in porous media and exploring unknown flow patterns at pore scale. ... -
Thermodynamic and Economic Analysis Between Organic Rankine Cycle and Kalina Cycle for Waste Heat Recovery From Steam-Assisted Gravity Drainage Process in Oilfield
(The American Society of Mechanical Engineers (ASME), 2018)A thermodynamic and economic comparative analysis are presented for waste heat recovery (WHR) from the heavy oil production with steam-assisted gravity drainage (SAGD) process employing organic Rankine cycle (ORC) and ... -
A Study on a Copolymer Gelant With High Temperature Resistance for Conformance Control
(The American Society of Mechanical Engineers (ASME), 2018)Due to the limited temperature resistance, the deep conformance control technology of using the conventional hydrolyzed polyacrylamide (HPAM) gel failed to enhance oil recovery in high-temperature heterogeneous oil reservoirs. ... -
Experimental Investigation of Amine-Surfactant CO2 Foam Stability Enhanced by Silica Nanoparticles
(The American Society of Mechanical Engineers (ASME), 2018)The CO2 foam generated by the conventional surfactants usually does not show long-term stability due to the substantial solubility and diffusivity of CO2 in water. Silica nanoparticles with different wettability and high ... -
Effect of Slick Water on Permeability of Shale Gas Reservoirs
(The American Society of Mechanical Engineers (ASME), 2018)In this study, we analyzed the flow-back resistance of slick water fracturing fluid in shale reservoirs. The flow-back resistance mainly includes capillary force, Van der Waals (VDW) force, hydrogen bond force, and hydration ... -
Analysis of the Flue Gas Preparation Process for the Purposes of Carbon Dioxide Separation Using the Adsorption Methods
(The American Society of Mechanical Engineers (ASME), 2018)The necessity of limitation of carbon dioxide emissions, which also concerns the energy sector, causes that more and more effective and efficient methods of CO2 capture from the flue gas are being tested. Among these ... -
Effects of Non-Darcy Flow and Penetrating Ratio on Performance of Horizontal Wells With Multiple Fractures in a Tight Formation
(The American Society of Mechanical Engineers (ASME), 2018)A novel slab source function has been formulated and successfully applied to examine effects of non-Darcy flow and penetrating ratio on performance of a horizontal well with multiple fractures in a tight formation. The ... -
Theoretical Prediction of the Effect of Blending JP-8 With Syngas on the Ignition Delay Time and Laminar Burning Speed
(The American Society of Mechanical Engineers (ASME), 2018)A numerical study has been carried out to investigate the impact of adding syngas into JP-8 fuel. A new chemical mechanism has been assembled from existing mechanism of JP-8 and syngas and has been examined by comparing ... -
Numerical and Experimental Investigation on Flow Capacity and Erosion Wear of Blooey Line in Gas Drilling
(The American Society of Mechanical Engineers (ASME), 2018)Blooey line is a discharge pipe, used to conduct gas to keep drilling rock dust and cuttings away from the drilling rig, reducing the fire hazard and transporting the cuttings to a suitable distance from the well. In this ... -
Effect of Char Structure Evolution During Pyrolysis on Combustion Characteristics and Kinetics of Waste Biomass
(The American Society of Mechanical Engineers (ASME), 2018)Two waste biomass materials, pine needle (PN) and corn stalk (CS), were pyrolyzed at different temperatures (200–900 °C). The organic functional groups and carbonaceous structure of the biomass chars were characterized by ... -
Improving Efficiency of the Tip Speed Ratio-MPPT Method for Wind Energy Systems by Using an Integral Sliding Mode Voltage Regulator
(The American Society of Mechanical Engineers (ASME), 2018)This paper aims to increase the efficiency of the maximum power point tracking (MPPT) methods by using an integral sliding mode voltage regulator (ISMVR). The ISMVR is applied to one of the frequently used MPPT methods ...