Journal of Energy Resources Technology: Recent submissions
Now showing items 1021-1040 of 3450
-
Experimental Study of Laminar Burning Speed for Premixed Biomass/Air Flame
(The American Society of Mechanical Engineers (ASME), 2019)Biomass has been considered as a valuable alternative fuel recently. A fundamental property of biomass/air flame, laminar burning speed, is measured in this research. Experiments have been made in a cylindrical combustion ... -
Stability Analysis of Highly Deviated Boreholes to Minimize Drilling Risks and Nonproductive Time
(The American Society of Mechanical Engineers (ASME), 2019)The Lower Cretaceous Zubair Formation is a regionally extended gas- and oil-producing sandstone sequence in Southern Iraq. Due to the weak nature of the Zubair Formation, the lack of wellbore stability is one of the most ... -
The Critical Pressure at the Onset of Flame Instability of Syngas/Air/Diluent Outwardly Expanding Flame at Different Initial Temperatures and Pressures
(The American Society of Mechanical Engineers (ASME), 2019)Syngas has gained attention recently due to its high energy density and environmentally friendly characteristics. Flame stability plays an important role in flame propagation in energy conversion devices. Experimental ... -
A Study on the Capability of Backward Swept Blades to Mitigate Loads of Wind Turbines in Shear Flow
(The American Society of Mechanical Engineers (ASME), 2019)The vertical wind shear is one of the major sources of fatigue loads on the blades of a horizontal axis wind turbine. Traditionally, the active individual pitch control system is used to alleviate the cyclic load fluctuations, ... -
Weighted Least Squares Approach for an Adaptive Aerodynamic Engineered Structure With Twist Transformation
(The American Society of Mechanical Engineers (ASME), 2019)A design concept for a wind turbine blade with an adaptive twist transformation is presented. The design improves partial-load wind capture by adapting the twist distribution in relation to wind speed. Structural adaptability ... -
Understanding the Effect of Oxygenated Additives on Combustion Characteristics of Gasoline
(The American Society of Mechanical Engineers (ASME), 2019)Laminar burning speed and ignition delay time behavior of iso-octane at the presence of two different biofuels, ethanol and 2,5 dimethyl furan (DMF), was studied in this work. Biofuels are considered as a better alternative ... -
Performance Effects of Leading Edge Tubercles on the NREL Phase VI Wind Turbine Blade
(The American Society of Mechanical Engineers (ASME), 2019)Several studies on wind energy have been conducted to find possible solutions to power issues related to the variable nature of the wind. One of the most promising seems to be the application of sinusoidal modifications ... -
Vertical Axis Wind Turbine Aerodynamics: Summary and Review of Momentum Models
(The American Society of Mechanical Engineers (ASME), 2019)Momentum models or streamtube models represent one of the fundamental approaches in modeling the aerodynamics of straight bladed vertical axis wind turbine (SB-VAWT) of Darrieus type. They are based on momentum (actuator ... -
Combustion Simulation of Propane/Oxygen (With Nitrogen/Argon) Mixtures Using Rate-Controlled Constrained-Equilibrium
(The American Society of Mechanical Engineers (ASME), 2019)The rate-controlled constrained-equilibrium (RCCE), a model order reduction method, has been further developed to simulate the combustion of propane/oxygen mixture diluted with nitrogen or argon. The RCCE method assumes ... -
Study on the Reoxidation Characteristics of Soaked and Air-Dried Coal
(The American Society of Mechanical Engineers (ASME), 2019)After coal seam mining, the residual coal is soaked with the accumulated water in goaf, and its spontaneous combustion characteristics were changed after air-dried. To study the reoxidation characteristics of soaked and ... -
Effect of Cavity Coupling Factors of Opposed Counter-Flow Microcombustor on the Methane-Fueled Catalytic Combustion Characteristics
(The American Society of Mechanical Engineers (ASME), 2019)In this work, numerical investigations of methane catalytic combustion in the opposed counter-flow microcombustor are conducted under various inlet velocities, equivalence ratios, and geometric parameters. The results ... -
Hydrocarbon Recovery From Oil Sands by Cyclic Surfactant Solubilization in Single-Phase Microemulsions
(The American Society of Mechanical Engineers (ASME), 2019)Extra heavy crude oil (bitumen) reserves represent a significant part of the energy resources found all over the world. In Canada, the “oil sands” deposits are typically unconsolidated, water-wet media where current methods ... -
The Rate-Controlled Constrained-Equilibrium Combustion Modeling of n-Pentane/Oxygen/Diluent Mixtures
(The American Society of Mechanical Engineers (ASME), 2019)Rate-controlled constrained equilibrium (RCCE) is a reduction technique used to describe the time evolution of complex chemical reacting systems. This method is based on the assumption that a nonequilibrium system can reach ... -
Effect of Carbon Dioxide on the Laminar Burning Speed of Propane–Air Mixtures
(The American Society of Mechanical Engineers (ASME), 2019)This experimental research examined the effect of CO2 as a diluent on the laminar burning speed of propane–air mixtures. Combustion took place at various CO2 concentrations (0–80%), different equivalence ratios (0.7<ϕ<1.2) ... -
A Proposed Biodiesel Combustion Kinetics Based on the Computational Fluid Dynamics Results in an Ignition Quality Tester
(The American Society of Mechanical Engineers (ASME), 2019)In this paper, five biodiesel global combustion decomposition steps are added to a surrogate mechanism to accurately represent the chemical kinetics of the decomposition of different levels of saturation of biodiesel, which ... -
Effects of Dilute Phosphoric Acid Treatment on Structure and Burning Characteristics of Lignocellulosic Biomass
(The American Society of Mechanical Engineers (ASME), 2019)Pretreatment of biomass with phosphoric acid (H3PO4) has been a popular method since it facilitates the generation of biofuels and mitigates the problems arising from the use of corrosive sulfuric acid that is otherwise ... -
Numerical Study on the First Stage Head Degradation in an Electrical Submersible Pump With Population Balance Model
(The American Society of Mechanical Engineers (ASME), 2019)Based on previous experiment result, an assumption is made to explain the abnormal head degradation in the first stage of an electrical submersible pump (ESP): the bubbles' breaking up and coalescence effect with compressibility ... -
Nitrogen-Bearing Emissions From Burning Corn Straw in a Fixed-Bed Reactor: Effects of Fuel Moisture, Torrefaction, and Air Flowrate
(The American Society of Mechanical Engineers (ASME), 2019)Combustion-generated emissions of acid gases, such as nitrogen-bearing species, constitute environmental pollutants and some are subjected to environmental regulations. Assessment of such emissions is important to decide ... -
Energy Conversion by Nanomaterial-Based Trapezoidal-Shaped Leg of Thermoelectric Generator Considering Convection Heat Transfer Effect
(The American Society of Mechanical Engineers (ASME), 2019)Thermoelectric generators (TEGs) can harvest energy without any negative environmental impact using low potential sources, such as waste heat, and subsequently convert that energy into electricity. Different shaped leg ... -
Modeling and Operational Optimization Based on Energy Hubs for Complex Energy Networks With Distributed Energy Resources
(The American Society of Mechanical Engineers (ASME), 2019)Energy hubs is an integrated system which is capable of transporting, transforming, and storing several types of energy. A number of hubs can be combined as a network and achieve higher efficiency by exchanging information ...