Journal of Heat Transfer: Recent submissions
Now showing items 3321-3340 of 3611
-
Heat Conduction Through Heat Exchanger Tubes of Noncircular Cross Section
(The American Society of Mechanical Engineers (ASME), 2008)Conduction through shaped tubes with circular inner surface and hydrodynamically shaped outer surface has been analyzed by two different techniques. A two-dimensional analysis has been made by a ... -
Moving Boundary-Moving Mesh Analysis of Freezing Process in Water-Saturated Porous Media Using a Combined Transfinite Interpolation and PDE Mapping Methods
(The American Society of Mechanical Engineers (ASME), 2008)This paper couples the grid generation algorithm with the heat transport equations and applies them to simulate the thermal behavior of freezing process in water-saturated porous media. Focus ... -
Genetic Algorithm Based Optimization of PCM Based Heat Sinks and Effect of Heat Sink Parameters on Operational Time
(The American Society of Mechanical Engineers (ASME), 2008)Using an approach that couples genetic algorithm (GA) with conventional numerical simulations, optimization of the geometric configuration of a phase-change material based heat sink (PBHS) is ... -
Subcooled Boiling Flow Heat Transfer From Plain and Enhanced Surfaces in Automotive Applications
(The American Society of Mechanical Engineers (ASME), 2008)The requirement for the highest possible heat transfer rates in compact, efficient cooling systems can often only be met by providing for a transition to subcooled boiling flow in strongly ... -
Heat Transfer in the Flow of a Cold, Axisymmetric Vertical Liquid Jet Against a Hot, Horizontal Plate
(The American Society of Mechanical Engineers (ASME), 2008)The paper considers heat transfer characteristics of thin film flow over a hot horizontal flat plate resulting from a cold vertical jet of liquid falling onto the surface. A numerical solution ... -
Dynamic Behavior of Three-Fluid Crossflow Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 2008)A transient temperature response of three-fluid heat exchangers with finite and large capacitance of the separating sheets is investigated numerically for step, ramp, exponential, and sinusoidal ... -
Film Cooling and Heat Transfer on Two Cutback Trailing Edge Models With Internal Perforated Blockages
(The American Society of Mechanical Engineers (ASME), 2008)Experiments to study heat transfer and film cooling on the cutback trailing edge of a turbine blade with slot ejection were performed. Heat transfer from two rows of perforated blockage inserts ... -
Study on Micropump Using Boiling Bubbles
(The American Society of Mechanical Engineers (ASME), 2008)A micropump was developed using boiling and condensation in a microchannel. The length and hydraulic diameter of the semi-half-circle cross-section microchannel having two open tanks at both ends ... -
Analytical Solution for Heat Conduction Near an Encapsulated Sphere With Heat Generation
(The American Society of Mechanical Engineers (ASME), 2008)The analytic study of heat conduction near spheres is a relatively mature science. Even so, there are still a number of analytic conduction solutions being published. For example, Atefi and ... -
Rewetting Analysis of Hot Vertical Surfaces With Precursory Cooling by the Heat Balance Integral Method
(The American Society of Mechanical Engineers (ASME), 2008)The effect of precursory cooling on conduction-controlled rewetting of both slab and solid cylinder is analyzed by the heat balance integral method. A constant heat transfer coefficient is assumed ... -
Simulation of Thermal Transport in Open-Cell Metal Foams: Effect of Periodic Unit-Cell Structure
(The American Society of Mechanical Engineers (ASME), 2008)Direct simulation of thermal transport in open-cell metal foams is conducted using different periodic unit-cell geometries. The periodic unit-cell structures are constructed by assuming the pore ... -
Thermophysical Properties of Biporous Heat Pipe Evaporators
(The American Society of Mechanical Engineers (ASME), 2008)Thirty biporous slugs with 3 different cluster diameters and 5 different particle diameters (15 combinations with 2 repetitions) and 12 monoporous slugs with 6 different particle diameters were ... -
Heat-Transfer Enhancement by Chaotic Advection in the Eccentric Helical Annular Flow
(The American Society of Mechanical Engineers (ASME), 2008)Chaotic advection in the eccentric helical annular heat exchanger is investigated as a means to enhance its thermal efficiency. Chaotic streak lines are generated by steadily rotating one boundary ... -
Effective Thermal Diffusivity of Porous Media in the Wall Vicinity
(The American Society of Mechanical Engineers (ASME), 2008)Transient heat transfer from an impulsively heated vertical constant heat flux plate embedded in a stationary saturated porous medium is studied experimentally and analytically to determine near-wall ... -
Discussion “Pressure Drop During Refrigerant Condensation Inside Horizontal Smooth, Helical Microfin, and Herringbone Microfin Tubes” (Olivier, J. A., Liebenberg, L., Kedzierski, M. A., and Meyer, J. P., 2004, J. Heat Transfer, 126(5), pp. 687–696)
(The American Society of Mechanical Engineers (ASME), 2008)In the paper “Pressure Drop During Refrigerant Condensation Inside Horizontal Smooth, Helical Microfin, and Herringbone Microfin Tubes” (Olivier, J. A., Liebenberg, L., Kedzierski, M. A., and ... -
Influence of Inelastic Scattering at Metal-Dielectric Interfaces
(The American Society of Mechanical Engineers (ASME), 2008)Thermal boundary conductance is becoming increasingly important in microelectronic device design and thermal management. Although there has been much success in predicting and modeling thermal ... -
Influence of a Coflowing Ambient Stream on a Turbulent Axisymmetric Buoyant Jet
(The American Society of Mechanical Engineers (ASME), 2008)This paper reports numerical results on turbulent buoyant axisymmetric jets in a coflowing ambient stream. The objective of this study is to compare the performance of the Reynolds stress ... -
Exergy Analysis of Data Center Thermal Management Systems
(The American Society of Mechanical Engineers (ASME), 2008)The modeling of recirculation patterns in air-cooled data centers is of interest to ensure adequate thermal management of computer racks at increased heat densities. Most metrics that describe ... -
Temperature Scalings and Profiles in Forced Convection Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 2008)Based on the theory of similarity analysis and the analogy between momentum and energy transport equations, the temperature scalings have been derived for forced convection turbulent boundary ... -
Thermal Transport in a Microchannel Exhibiting Ultrahydrophobic Microribs Maintained at Constant Temperature
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents numerical results exploring the periodically repeating laminar flow thermal transport in a parallel-plate microchannel with ultrahydrophobic walls maintained at constant temperature. ...