Journal of Structural Engineering: Recent submissions
Now showing items 4761-4780 of 10765
-
Blast Resistance Capacity of Reinforced Concrete Slabs
(American Society of Civil Engineers, 2009)This paper presents the basis of a procedure to estimate the explosive charge weight and stand-off distance to impose certain levels of damage on reinforced concrete (RC) structures. A series of experiments were also ... -
Flexural Buckling of Elliptical Hollow Section Columns
(American Society of Civil Engineers, 2009)Complementary to recent studies on the cross-section behavior of elliptical hollow sections, investigations into the member response have also been performed and described in this paper. The first stage of these investigations ... -
Design of Aluminum Alloy Flexural Members Using Direct Strength Method
(American Society of Civil Engineers, 2009)This paper presents the experimental and numerical investigation of aluminum alloy flexural members. The tests were performed on ten different sizes of square hollow sections subjected to pure bending. Material properties ... -
Design of Buckling-Restrained Braced Frames Using Nonlinear Time History Analysis and Optimization
(American Society of Civil Engineers, 2009)A procedure for the design of buckling-restrained braced frames is presented. The procedure uses nonlinear time history analysis and optimization. Results from this procedure are compared to those from the commonly used ... -
Design of Steel Equal Angle Lintels
(American Society of Civil Engineers, 2009)Single equal angle steel beams are often used as lintels to support eccentric loading acting normal to one flange. This loading causes combined biaxial bending and torsion, which is not allowed for in most steel design ... -
Inhibiting Steel Brace Buckling Using Carbon Fiber-Reinforced Polymers: Large-Scale Tests
(American Society of Civil Engineers, 2009)A new method is proposed for inhibiting the buckling response of steel braces. The strengthening technique involves attaching a core comprised of mortar blocks to the braces and then wrapping the entire system with carbon ... -
Stiffness Reduction Factor for Flat Slab Structures under Lateral Loads
(American Society of Civil Engineers, 2009)Effective beam width model (EBWM) has been widely used for predicting lateral drifts and slab moments in flat slab structures under lateral loads. As the slab moment due to lateral loads increases, slab stiffness decreases ... -
Automated Finite-Element-Based Validation of Structures Designed by the Strut-and-Tie Method
(American Society of Civil Engineers, 2010)Several codes of practice now support the use of the strut-and-tie method (STM) for the design of complex regions in structural concrete. In this method, a load-resisting truss is idealized and designed to carry the applied ... -
Correlation of Beam Tests with Pushout Tests in Steel-Concrete Composite Beams
(American Society of Civil Engineers, 2010)Controversy has risen about the suitability of small-scaled pushout tests to satisfactorily model the behavior of shear connections in composite beams. However, the determination of the strength of the shear connectors ... -
Automatic DR Structural Analysis of Snap-Through and Snap-Back Using Optimized Load Increments
(American Society of Civil Engineers, 2011)In this paper, new schemes are presented for the dynamic relaxation (DR) method so that the snap-through and the snap-back regions can be traced automatically. These procedures are based on the minimization of the residual ... -
Parametric Estimation for RC Flexural Members Based on Distributed Long-Gauge Fiber Optic Sensors
(American Society of Civil Engineers, 2010)Long-term monitoring on the degradation of concrete structures has been a major engineering concern in many parts of the world. On the basis of the distributed long-gauge fiber optic sensors recently developed at Ibaraki ... -
Modular High-Force Seismic Magneto-Rheological Fluid Damper
(American Society of Civil Engineers, 2010)In this work, a large-scale magneto-rheological fluid (MRF) bypass valve damper for seismic mitigation applications is designed, constructed, and tested. The damper utilizes a simple design, with a modular bypass MRF valve, ... -
Tall Building Response Parameters: Sensitivity Study Based on Orthogonal Factorial Experiment Design Technique
(American Society of Civil Engineers, 2010)This work has two objectives. The first objective is to introduce structural engineers to the experiment design technique, whose future applications may include, for example, the total response of tall buildings, the ... -
New Reference Wind Speed for Wind Turbines in Typhoon-Prone Areas in the Philippines
(American Society of Civil Engineers, 2010)The Philippines has good potential for wind energy utilization. However, it is also prone to strong typhoons. Thus, wind turbines that will be erected in these areas maybe categorized into a special safety class and the ... -
Inelastic Effective Length Factor of Nonsway Reinforced Concrete Columns
(American Society of Civil Engineers, 2009)This paper proposes a new equation for the effective length factor ( -
Effects of Bottom Reinforcement on Hysteretic Behavior of Posttensioned Flat Plate Connections
(American Society of Civil Engineers, 2009)Flat plate systems are commonly designed as a gravity-force-resisting system (GFRS) along with stiffer lateral-force-resisting systems (LFRS) such as shear walls, and moment resisting frames; however, deformation compatibility ... -
Structural Damage Detection of Cable-Stayed Bridges Using Changes in Cable Forces and Model Updating
(American Society of Civil Engineers, 2009)A new static-based method for damage detection of cable-stayed bridges using the changes in cable forces is presented in this paper. In recognizing the fact that damage incurring in bridge girders will cause a redistribution ... -
Experimental Studies on Real-Time Testing of Structures with Elastomeric Dampers
(American Society of Civil Engineers, 2009)Real-time pseudodynamic (PSD) and hybrid PSD methods are a means to evaluate structural performance under dynamic loading when a component of a structural system cannot be accurately modeled and is load rate dependent. The ... -
Failure of Lightly Reinforced Concrete Floor Slabs with Planar Edge Restraints under Fire
(American Society of Civil Engineers, 2009)This paper presents an analytical model for the failure of lightly reinforced concrete slabs under elevated temperature, considering simply supported boundary conditions with planar edge restraints. This model is typically ... -
Macroscopic Elastic Constitutive Relationship of Cast-in-Place Hollow-Core Slabs
(American Society of Civil Engineers, 2009)The macroscopic Poisson ratio and elastic moduli of the cast-in-place hollow-core slab are researched in this paper. At first, the formulas for computing the Poisson’s ratio of cast-in-place hollowed slabs with bilateral ...