Journal of Structural Engineering: Recent submissions
Now showing items 4141-4160 of 10765
-
Developments on the Design of Cold-Formed Steel Angles
(American Society of Civil Engineers, 2013)This paper presents procedures for the design of fixed- and pin-ended equal-leg angle columns with short-to-intermediate lengths. First, some remarks concerning the buckling and postbuckling behavior of the angle columns ... -
Carrying Capacity of Stainless Steel Columns in the Low Slenderness Range
(American Society of Civil Engineers, 2013)The strength of thin-walled stainless steel columns has been investigated extensively over the last few years. In European standards, the concept of section classification for determining the cross section capacity is used. ... -
Behavior of Concrete and ECC Structures under Simulated Earthquake Motion
(American Society of Civil Engineers, 2013)The objective of the research presented in this paper is to investigate, experimentally, the effect of material- and section-level parameters on the structural response of concrete and engineered cementitious composite ... -
Cyclic Behavior of Corrugated Steel Shear Diaphragms with End Failure
(American Society of Civil Engineers, 2013)Light-gauge steel frames with load-bearing walls have become one option in robust structural systems for low-rise buildings. This structural system is often used in steel-framed houses and in typical load-bearing walls ... -
Analysis-Based Design Provisions for Steel Storage Racks
(American Society of Civil Engineers, 2013)The paper summarizes the main new design provisions included in the recently revised Australian standard for steel storage racks. The standard features multitiered analysis provisions ranging from basic linear-elastic ... -
Economical Steel Plate Shear Walls for Low-Seismic Regions
(American Society of Civil Engineers, 2013)Previous research on steel plate shear walls (SPSWs) and current design codes have focused principally on achieving highly ductile behavior through stringent detailing requirements. As such, the system is generally considered ... -
Theoretical and Experimental Study of Plate-Strengthened Concrete Columns under Eccentric Compression Loading
(American Society of Civil Engineers, 2013)Steel jacketing has been widely used for strengthening RC columns in the last four decades. In practice, the RC columns to be strengthened are usually subjected to eccentric precompressed axial loads. Until now, there have ... -
Seismic Performance of a Large-Scale Steel Self-Centering Moment-Resisting Frame: MCE Hybrid Simulations and Quasi-Static Pushover Tests
(American Society of Civil Engineers, 2013)This paper presents an experimental study of a 0.6-scale 2-bay 4-story steel self-centering moment-resisting frame (SC-MRF) test structure under maximum considered earthquake (MCE) ground motions. A SC-MRF uses high-strength ... -
Static and Dynamic Stability of Elastomeric Bearings for Seismic Protection of Structures
(American Society of Civil Engineers, 2013)Bearings used in the seismic isolation of buildings can be subjected to large horizontal deformations combined with high axial loads from overturning forces during strong shaking. Elastomeric bearing design requires an ... -
Structural Behavior of RC Beam-Column Subassemblages under a Middle Column Removal Scenario
(American Society of Civil Engineers, 2013)Six RC beam-column subassemblages, consisting of two single-bay beams, one middle joint, and two end column stubs, were quasi-statically tested under a middle column removal scenario. The tests were aimed at investigating ... -
Experimental Seismic Fragility of Cold-Formed Steel Framed Gypsum Partition Walls
(American Society of Civil Engineers, 2013)As part of the Network for Earthquake Engineering Simulation Research (NEESR)-Grand Challenge Project Simulation of the Seismic Performance of Nonstructural Systems, an experimental program was carried out to evaluate the ... -
Experiments on Cold-Formed Steel C-Section Joists with Unstiffened Web Holes
(American Society of Civil Engineers, 2013)Experiments were conducted on cold-formed steel C-section joists with rectangular unstiffened web holes. The presence of holes decreased joist capacity and amplified distortional buckling deformation. Distortional buckling ... -
Net Section Tension Capacity of Cold-Reduced Sheet Steel Channel Braces Bolted at the Web
(American Society of Civil Engineers, 2013)This paper examines the accuracy of equations specified by the North American and Australasian steel structures codes for determining the net section tension capacity of a channel brace. It points out that there are three ... -
Approximating Frequencies of Tall Buildings
(American Society of Civil Engineers, 2013)A Rayleigh quotient is developed to calculate estimates of the fundamental frequencies of tall slender buildings. The quotient provides simple analytical frequency estimates that agree well with results reported using a ... -
Efficient and Accurate Method for Calculating the Stochastic Seismic Response of a Nonproportionally Damped Structure
(American Society of Civil Engineers, 2013)In the case of nonproportionally damped structures, the forced decoupling method is often adopted in approximate analysis. However, it generally cannot satisfy the precision requirements for practical engineering. Taking ... -
Buckling, Postbuckling, Strength, and DSM Design of Cold-Formed Steel Continuous Lipped Channel Beams
(American Society of Civil Engineers, 2013)The work reported in this paper is part of an ongoing numerical investigation aimed at (1) assessing the buckling, postbuckling, strength, and collapse behavior of cold-formed steel continuous beams and simple frames and ... -
Performance-Based Seismic Design of Midrise Woodframe Buildings
(American Society of Civil Engineers, 2013)The understanding of, and ability to predict, the seismic behavior of woodframe structures has improved immensely in the last 10 years. Two notable projects occurred in succession, the Consortium of Universities for Research ... -
Use of the Wind Tunnel Test Method for Obtaining Design Wind Loads on Roof-Mounted Solar Arrays
(American Society of Civil Engineers, 2013)ASCE 7 does not provide design wind loads for roof-mounted solar panels. This paper discusses the use of the wind tunnel test method, called Method 3 in ASCE 7-05, which was originally intended for obtaining design wind ... -
Simulation-Based Fragility Relationships for Unreinforced Masonry Buildings
(American Society of Civil Engineers, 2013)Unreinforced masonry (URM) structures represent a significant portion of the residential building stock of the central and eastern United States. Fifteen percent of homes in the eight-state region impacted by the New Madrid ... -
Evaluation of Tsunami Loads on Wood-Frame Walls at Full Scale
(American Society of Civil Engineers, 2013)The performance of full-scale light-frame wood walls subjected to wave loading was examined using the Large Wave Flume of the Network for Earthquake Engineering (NEES) Tsunami Facility at Oregon State University. The ...