Journal of Structural Engineering: Recent submissions
Now showing items 4021-4040 of 10765
-
Static Strength of Axially Loaded Elliptical Hollow Section X Joints with Braces Welded to Wide Sides of Chord. I: Numerical Investigations Based on Experimental Tests
(American Society of Civil Engineers, 2014)Experimental tests and subsequent finite-element (FE) calibration studies were conducted to study the static strength of axially loaded X joints between elliptical hollow sections (EHS) with braces welded to the wide sides ... -
Experimental Study on Compressive Bond Anchorage Properties of 500 MPa Steel Bars in Concrete
(American Society of Civil Engineers, 2013)Few studies on the anchorage of reinforcing bars under the compressive conditions have been undertaken. This paper reports the results of 99 pushout tests done to investigate the compressive bond anchorage properties of ... -
Eccentricity-Based Optimization Procedure for Strength Design of RC Sections under Compression and In-Plane Bending Moment
(American Society of Civil Engineers, 2014)The strength design of reinforced concrete (RC) rectangular sections for combined compression and in-plane bending with two levels of reinforcement is indeterminate: three unknowns are to be solved, but with only two ... -
Experimental Evidence of Erosion of Critical Load in Interactive Buckling
(American Society of Civil Engineers, 2013)The paper starts with a selective review of some basic contributions related to local-overall buckling mode interactions in thin-walled steel members. Then, the results of an intensive experimental study carried out at the ... -
Shake-Table Studies of a Four-Span Reinforced Concrete Bridge
(American Society of Civil Engineers, 2013)Shake-table response of a 33.6-m-long (110-ft-long), four-span, RC bridge model with a continuous posttensioned superstructure supported on three, two-column bents was studied under horizontal bidirectional coherent simulated ... -
Bending Performance of Box-Based Cross-Laminated Timber Systems
(American Society of Civil Engineers, 2013)Cross-laminated timber (CLT) is a growing phenomenon and a recent building solution alternative in timber construction in North America by using massive or solid wood plates as roof, floor, and wall elements. In this paper ... -
Fire Resistance of Cross-Laminated Timber Panels Loaded Out of Plane
(American Society of Civil Engineers, 2013)This paper describes bending tests at ambient temperature and large-scale fire tests of cross-laminated timber (Xlam) floor panels. Three specimens exposed to standard fire curve were loaded out-of-plane with different ... -
Strength of Circular Concrete-Filled Tubes with and without Internal Reinforcement under Combined Loading
(American Society of Civil Engineers, 2013)Concrete-filled tubes (CFTs) have been used in civil engineering practice as piles, caissons, columns, and bridge piers. Relative to conventional structural steel and reinforced concrete components, CFTs have several ... -
Full-Scale Tests of Slender Concrete-Filled Tubes: Axial Behavior
(American Society of Civil Engineers, 2013)Composite steel-concrete columns and beam-columns have been shown to provide superior performance when the intrinsic synergistic characteristics of concrete and steel are properly exploited. However, limited test data are ... -
Effect of Shear Wall Area to Floor Area Ratio on the Seismic Behavior of Reinforced Concrete Buildings
(American Society of Civil Engineers, 2013)An analytical study is performed to evaluate the effect of shear wall area to floor area ratio on the seismic behavior of midrise RC structures. For this purpose, 24 midrise building models that have five and eight stories ... -
Reviewers
(American Society of Civil Engineers, 2013) -
Development of an Axial Load Capacity Equation for Doubly Symmetric Built-Up Cold-Formed Sections
(American Society of Civil Engineers, 2013)This work aims to develop an axial load capacity equation for doubly symmetric built-up cold-formed sections with a sufficient number of intermediate, symmetrical connections. A numerical parametric study involving a total ... -
Stability of Z-Section Purlins Used as Temporary Struts during Construction
(American Society of Civil Engineers, 2013)The stability of Z purlins subject to combined axial force and biaxial bending due to self-weight (a situation that typically arises during construction) is investigated. Single, isolated purlins as well as purlins with ... -
Monitoring Crack Propagation in Reinforced Concrete Shear Walls by Acoustic Emission
(American Society of Civil Engineers, 2013)In the last two decades, several efforts have been made to monitor the cracking behavior in RC structures. A technique that shows promise is acoustic emission (AE). This paper presents the results of an experimental study ... -
Effects of Assembly Tolerances on Bolted Anchorages in Concrete
(American Society of Civil Engineers, 2014)The performance of concrete anchors located close to a free edge and loaded in shear toward the edge of a concrete member is influenced by several geometric and structural/material parameters. In the case of anchor groups, ... -
Effects of Simulated Corrosion and Delamination on Response of Two-Way Slabs
(American Society of Civil Engineers, 2014)This paper presents the results from an experimental program that studied the effects of simulated delamination and corrosion on the structural response of six two-way slab-column specimens with details typical of older ... -
Blast Modeling of Steel Frames with Simple Connections
(American Society of Civil Engineers, 2014)This paper is concerned with the problem that structural joints in whole-frame models cannot, at present, be replicated in sufficiently minute detail to realistically represent their behavior. It is well recognized that ... -
Effect of Manufacturing Factors on Technological Properties of Plywood from Northern Turkey and Suitability of Panels for Use in Shear Walls
(American Society of Civil Engineers, 2013)Shear walls provide the lateral resistance needed for light-frame wood structures to withstand earthquake and wind loads. When sheathed with wooden structural panels, shear walls can be strong, stiff, and ductile. This is ... -
Accurate Application and Second-Order Improvement of SAC/FEMA Probabilistic Formats for Seismic Performance Assessment<sup>1</sup>
(American Society of Civil Engineers, 2014)The SEAONC/ATC/CUREE (SAC/FEMA) probabilistic framework is based on a closed-form expression to estimate analytically the value of the risk integral convolving seismic hazard and structural response. Despite its practicality, ... -
Bending Properties of Wood I-Sections Fabricated with Screws and Polyurethane Adhesive
(American Society of Civil Engineers, 2013)Laboratory tests were used to quantify the effects of section shape, screw density, and polyurethane adhesive use on laminated wood assembly bending strength and stiffness. Both I-shaped sections and vertically laminated ...