Journal of Structural Engineering: Recent submissions
Now showing items 1441-1460 of 10765
-
Influence of Steel Reinforcement on the Performance of Elastomeric Bearings
(ASCE, 10/1/2020 )Seismic isolation is an effective measure for mitigating earthquake hazard on important structures such as bridges, hospitals, and nuclear power plants. Seismically isolated structures should remain essentially elastic for ... -
Influence of Sheathing-Fastener Connection Stiffness on the Design Strength of Cold-Formed Steel Wall Panels
(ASCE, 10/1/2020 )This paper investigates the bracing effect of sheathing fastener connection on point-symmetric shaped cold formed steel (CFS) studs through full-scale laboratory tests. The test parameters include slenderness of the CFS ... -
Column Curves for Stainless Steel Lipped–Channel Sections
(ASCE, 10/1/2020 )The strength of thin-walled stainless steel columns has been investigated extensively over the last few years. The present paper presents the results of an extensive computational study of the buckling strength of ... -
Air-Permeability Factor for Wind Loads on Loose-Laid Pavers on Flat Roofs
(ASCE, 8/1/2020 1)Installation of open-joint roof paver systems with pedestals on flat roofs leaves a cavity between pavers and roof deck, allowing the development of cavity pressure. The cavity suction on roof pavers reduces the net wind ... -
Transverse Stiffener Requirements for Shear Postbuckling of Cold-Formed Steel Channels
(ASCE, 8/1/2020 1)The enhanced shear strength of transversely stiffened shear panels compared to the strengths of the unstiffened has been well recognized in the Specification for Structural Steel Buildings (AISC 360) and the North American ... -
Experimental and Analytical Study on the Shear-Strength of Partially Grouted Masonry Walls
(ASCE, 8/1/2020 1)This paper reports on an experimental study of six full-scale partially grouted masonry walls (PG-MWs), and evaluated the accuracy of international design codes based on the test results. The main test parameters were the ... -
Effects of High-Frequency Ground-Motion Spectra in the Seismic Response of Squat RC Walls
(ASCE, 8/1/2020 1)Due to the high-frequency content of ground motions in central and eastern United States (CEUS) sites, the US Nuclear Regulatory Commission has modified their regulatory guides to consider these effects in the evaluation ... -
Uniaxial Eccentric-Compression Performance Analysis for Double-Plate Connected Concrete-Filled Steel-Tube Composite Columns
(ASCE, 8/1/2020 1)In this study, five double-plate connected concrete-filled steel tube (CFST) composite columns were tested under a uniaxial eccentric compressive load. The test phenomena, load–axial displacement curves, strain analyses, ... -
Eccentric-Axial-Load Test for Composite Columns Using Bolt-Connected Steel Angles
(ASCE, 9/1/2020 1)For better structural performance and constructability, a concrete-encased steel column that uses a steel cage prefabricated with bolt connections was developed. The steel cage consists of longitudinal steel angles and ... -
Hysteresis Model for Fiber Elements in Effective Damaged Zone of Square-Section Steel Piers Considering Local Instability Effect of Steel Plates
(ASCE, 8/1/2020 1)The local instability of steel plates is the predominant seismic failure mode for steel bridge piers. However, the application of shell-based finite-element (FE) models in an engineering design presents significant ... -
Multiple-Damage State Retrofit of Steel MRFs with Composite Beams Using a Minimal-Disturbance Arm Damper
(ASCE, 9/1/2020 1)This study presents a design method for the seismic retrofit and rehabilitation of steel moment-resisting frames (MRFs) with composite steel–concrete beams using the minimal-disturbance arm damper (MDAD). The purpose is ... -
Hysteretic Behavior of Moment-Resisting Frames Considering Slab Restraint and Framing Action
(ASCE, 8/1/2020 1)This paper examines the influence of framing action and slab continuity on the hysteretic behavior of composite steel moment-resisting frames (MRFs) by means of high-fidelity continuum finite-element (CFE) analyses of ... -
Substructure Identification for an Axially Loaded Member Using Local Vibration Modes
(ASCE, 7/1/2020 1)Axially loaded elements play an important role in various civil structures. Knowledge of these crucial members is critical to health monitoring and performance assessment of a structure system in daily service or after a ... -
Effect of Charge Shape and Initiation Configuration of Explosive Cylinders Detonating in Free Air on Blast-Resistant Design
(ASCE, 8/1/2020 1)This paper investigates the influence of the cylindrical charge characteristics, i.e., the length-to-diameter ratio, orientation, and initiation configuration, on the blast loads (peak overpressure and maximum impulse). ... -
Concrete-Filled Elliptical Hollow Section Beam-Columns under Seismic Loading
(ASCE, 8/1/2020 1)The seismic behavior of elliptical hollow section (EHS) beam-column members was examined in this study. A comprehensive experimental investigation was conducted on 14 concrete-filled and four bare steel EHS beam-column ... -
Seismic Behavior of Welded Beam-to-Column Joints of High-Strength Steel-Moment Frame with Replaceable Damage-Control Fuses
(ASCE, 8/1/2020 1)This paper first proposes a high-strength (HS) steel-moment frame structure with replaceable damage-control fuses, which utilized the very large elastic deformation capacity of HS steel and damage-control functions of ... -
Experiments in a Large Boundary Layer Wind Tunnel: Upstream Terrain Effects on Surface Pressures Acting on a Low-Rise Structure
(ASCE, 8/1/2020 1)An extensive series of experiments in a large boundary layer wind tunnel (BLWT) was carried out at the University of Florida (UF) Natural Hazard Engineering Research Infrastructure (NHERI) Experimental Facility to investigate ... -
Simplified Analytical Model for Interfacial Bond Strength of Deformed Steel Rebars Embedded in Pre-cracked Concrete
(ASCE, 8/1/2020 1)Although extensive bond models have been developed for use in the numerical simulation of uncracked reinforced concrete, no simplified method exists providing satisfactory accuracy and efficiency for pre-cracked concrete. ... -
Full-Scale Cyclic Rotation and Shear-Load Testing of Double Web with Top and Seat Angle Beam-Column Connections
(ASCE, 8/1/2020 1)Partially restrained beam-column connections such as bolted double web with top and seat angle connections can be used in the gravity load system of steel buildings to develop secondary moment frame action and enhance ... -
Integrated Structural–Nonstructural Performance-Based Seismic Design and Retrofit Optimization of Buildings
(ASCE, 8/1/2020 1)The assessment of anticipated losses due to damage of both structural and nonstructural components is now recognized to be a key component in the performance-based seismic design or retrofit of buildings. Current ...