Journal of Micro and Nano
Browse by
EISSN:2166-0476|ISSN:2166-0468|Disc:The Journal of Micro and Nano-Manufacturing provides a forum for the rapid dissemination of original theoretical and applied research in the areas of micro- and nano-manufacturing that are related to process innovation, accuracy, and precision, throughput enhancement, material utilization, compact equipment development, environmental and life-cycle analysis, and predictive modeling of manufacturing processes with feature sizes less than one hundred micrometers. Papers addressing special needs in emerging areas, such as biomedical devices, drug manufacturing, water and energy, are also encouraged|Priority:4|Publisher:American Society of Mechanical Engineers|
Recent Submissions
-
A New Surface Finishing Process for Quartz Glass Rotary Parts Based on Changes in Wetting State
(The American Society of Mechanical Engineers (ASME), 2025)Quartz glass has wide applications in semiconductor technology, optical communication, optical instruments, inertial navigation, and other fields. Quartz glass parts are commonly machined by mechanical methods, and in ... -
Influence of Microwave-Treated Waste Aramid Fibers on the Mechanical Behavior of 3D-Printed Composite Materials
(The American Society of Mechanical Engineers (ASME), 2025)Industrial surface modification techniques are commonly employed to enhance the adhesion between polymer matrices and aramid fibers (AFs) in composite materials. However, these techniques are often associated with high ... -
Investigation of Virtual Impactor Design Parameters in Aerosol Jet Printing Using Computational Fluid Dynamics
(The American Society of Mechanical Engineers (ASME), 2025)Aerosol jet printing (AJP) is a direct-write additive manufacturing technique used to fabricate electronics, such as sensors, capacitors, and optoelectronic devices. It has gained significant attention in being able to ... -
A Review on Recent Progress of Biodegradable Magnetic Microrobots for Targeted Therapeutic Delivery: Materials, Structure Designs, and Fabrication Methods
(The American Society of Mechanical Engineers (ASME), 2024)Targeted therapeutic delivery employs various technologies to enable precise delivery of therapeutic agents (drugs or cells) to specific areas within the human body. Compared with traditional drug administration routes, ... -
An Experimental Study on Material Removal Mechanisms in Quasi-Continuous Wave Fiber Laser Microdrilling of SS 304
(The American Society of Mechanical Engineers (ASME), 2025)This paper investigates the different material removal mechanisms that occur during quasi-continuous wave (QCW) fiber laser drilling using millisecond pulses on stainless steel 304 samples and studies their effect on hole ... -
Design of Experiments Informed Investigation of Magnetic Field-Assisted Nickel Electroplating on Copper
(The American Society of Mechanical Engineers (ASME), 2025)Nickel coatings have demonstrated significant benefits in protecting copper from oxidation and fouling, thereby enhancing the longevity of copper-based components. This study employed an electroplating apparatus featuring ... -
Digital Microfluidics Automation of Oligonucleotide Assemblies
(The American Society of Mechanical Engineers (ASME), 2025)Digital microfluidics can be used to reliably automate repeated ligation steps to create accurate DNA products. This investigation demonstrates assembly of single-stranded and double-stranded DNA products on digital ... -
Fabrication and Characterization of Metallic Glass Nanowire-Anchored Microfluidic Channels
(The American Society of Mechanical Engineers (ASME), 2025)Nanowire-based microfluidic devices combine the strengths of microfluidics and nanostructures for applications in cell biology and chemical sensing. However, their use has been limited by the complexity of the fabrication ... -
Direct Printing of High-Resolution Metallic Three-Dimensional Microneedle Arrays Via Electrohydrodynamic Jet Printing
(The American Society of Mechanical Engineers (ASME), 2024)Three-dimensional (3D) microneedle arrays (MAs) have shown remarkable performances for a wide range of biomedical applications. Achieving advanced customizable 3D MAs for personalized research and treatment remain a ... -
Automated Grayscale Modulation to Enhance Digital Light Processing Fabrication Accuracy by Correcting Nonuniform Illumination
(The American Society of Mechanical Engineers (ASME), 2024)In this study, we addressed the challenge of nonuniform illumination in custom digital light processing (DLP) systems, often caused by imperfections in the digital micromirror device (DMD) or misalignments in the optical ... -
Comparative Analysis of Simultaneous Electrochemical and Electrodischarge Machining Process
(The American Society of Mechanical Engineers (ASME), 2024)Recent advances have established electrochemical discharge machining (ECDM) as an effective alternative to electrical discharge machining (EDM) for producing microholes in conductive materials. However, ECDM leaves nonuniform ... -
Rapid Modeling of Photopolymerization in Projection Two-Photon Lithography Via an Operator Splitting Finite Difference Method
(The American Society of Mechanical Engineers (ASME), 2024)Two-photon lithography (TPL) is an attractive technique for nanoscale additive manufacturing of functional three-dimensional (3D) structures due to its ability to print subdiffraction features with light. Despite its ... -
Aerosol Jet and Inkjet Printing Methods for Die-Level Packaging of Custom MEMS Devices
(The American Society of Mechanical Engineers (ASME), 2024)In this study, we propose an alternative, low-cost, packaging method using both inkjet and aerosol jet printing (AJP) to fabricate functional interconnects for custom die-level packages assembled on printed circuit boards ... -
Rapid Prototyping of Multiscale Flexible Printed Circuit Boards With NeXus, a Robotic Additive Manufacturing System
(The American Society of Mechanical Engineers (ASME), 2024)This paper demonstrates the NeXus system, a multiscale robotic additive manufacturing platform developed at the Louisville Automation and Robotics Research Institute, as a rapid prototyping tool through additively manufacturing ... -
On the Potential of Manufacturing Multi-Material Components With Micro/Nanocellular Structures Via the Hybrid Process of Electromagnetic Forming Injection Foaming
(The American Society of Mechanical Engineers (ASME), 2024)Multimaterial design with a combination of solid and foam structures offers a promising avenue for reducing component weight while enhancing their functionalities. However, the complexity of multistage manufacturing processes ... -
Laser Surface Texturing in Single-Point Incremental Sheet Forming
(The American Society of Mechanical Engineers (ASME), 2025)Single-point incremental sheet forming (SPIF) offers high flexibility, cost-effectiveness, mass customization, ease of setup, and scalability. However, the process can result in poor surface characteristics, making it ... -
Patternable Joule Heat Film With Ultrafast Heating, High-Temperature, and Oxidation-Resistant Surface
(The American Society of Mechanical Engineers (ASME), 2024)Ultrafast and ultrahigh temperature light sources are critical for advancements in energy, display, and security. However, their practical applications are hindered by limitations in oxidation resistance. Here, we address ... -
Effect of Laser Power and Diamond Tool Parameters for Micro Laser-Assisted Ductile Mode Material Removal on Fused Silica
(The American Society of Mechanical Engineers (ASME), 2024)Fused silica is an essential material used in various applications due to its excellent optical and mechanical properties. However, processing it can be challenging due to its high hardness and brittleness, leading to ... -
An Adaptive Spatial-Terminal Iterative Learning Strategy in Roll-to-Roll Control Problems
(The American Society of Mechanical Engineers (ASME), 2025)Roll-to-Roll (R2R) systems, featuring motorized or idle rollers, are crucial for high-volume, continuous production of flexible substrates. A significant challenge in R2R printing processes is maintaining tight alignment ... -
Surface Integrity Analysis of Niobium-Based Cermet Processed by Electrochemical Machining and Hybrid Laser-Electrochemical Machining
(The American Society of Mechanical Engineers (ASME), 2025)This study investigates the evolution of surface integrity of a strategically important niobium-based cermet with nickel binder (NbC–Ni), while processing it with electrochemical machining (ECM) and hybrid laser-ECM (LECM) ...