Journal of Thermal Science and Engineering Applications
Browse by
EISSN:1948-5093|ISSN:1948-5085|Disc:The Journal of Thermal Science and Engineering Applications focuses on the dissemination of information of permanent interest in applied thermal sciences and engineering emphasizing new and emerging technologies, significant questions, pressing problems and concerns, and new methods and approaches that can be applied to industrial problems. It complements the Journal of Heat Transfer, which focuses on fundamental research. Contributions must have clear relevancy to an industry, an industrial process, or a device. Subject areas could be as narrow as a particular phenomenon or device or as broad as a system. The Journal publishes original research of an applied nature; application of thermal sciences to processes or systems; technology reviews; and identification of research needs to solve industrial problems at all time and length scales. Contributions should describe research in applied areas pertaining to thermal energy transport in equipment and devices, thermal and chemical systems, and thermodynamic processes|Priority:6|Publisher:American Society of Mechanical Engineers|
Recent Submissions
-
Experimental Study on the Endwall Aerothermal Performance of Turbine Cascades in a Novel Transient Test Facility
(The American Society of Mechanical Engineers (ASME), 2024)Linear turbine cascades have been widely used to conduct fundamental and applied investigations, but only a few transient test facilities with the linear turbine cascade are available in the open literature. A novel transient ... -
Design of Encapsulated Phase Change Material Cooling Scheme for Compact 21700 Battery Modules
(The American Society of Mechanical Engineers (ASME), 2025)This article proposes a versatile thermal management solution utilizing phase change material (PCM) for compact 21700 battery modules. First, a flame-retardant and heat-conductive pouring sealant is utilized to encapsulate ... -
Wake Management and Capacity Augmentation by Toe-Out Type Vortex Generators in Finned-Tube Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 2025)Waste heat recovery usually involves indirect heat transfer, between two fluids, across a diathermic wall; and finned-type recuperative heat exchangers are preferred for the stipulated task. Strategic integration of vortex ... -
Experimental and Numerical Investigations on Thermal Interference of the Helix Ground Heat Exchanger for Ground Source Heat Pump System
(The American Society of Mechanical Engineers (ASME), 2025)This study conducted an investigation on the heat transfer process of helix ground heat exchanger (HGHE) by numerical simulation and experiment. The concept of thermal interference index was proposed, and the thermal ... -
Stochastic Modeling and Numerical Simulation of Carbon Fiber Felt for Effective Thermal Conductivity Considering Radiation Heat Transfer
(The American Society of Mechanical Engineers (ASME), 2025)Carbon fiber felt (CFF) has excellent thermal insulation ability under high-temperature environments. In this study, an algorithm for generating CFF microstructure models was developed. The heat transfer characteristic of ... -
Heat Transfer Coefficient Prediction and Increase the Effectiveness in Fin-and-Tube Heat Exchangers Using Machine Learning Approaches
(The American Society of Mechanical Engineers (ASME), 2025)The heat transfer coefficient (HTC) plays a crucial role in the efficiency and performance of heat exchangers, which are essential in numerous industrial applications. However, obtaining sufficient high-quality data for ... -
Optimization of District Heating Network Parameters in Steady-State Operation
(The American Society of Mechanical Engineers (ASME), 2024)We examine the modeling, simulation, and optimization of district heating systems, which are widely used for thermal transport using steam or hot water as a carrier. We propose a generalizable framework to specify network ... -
Design, Fabrication, and Testing of a Polymer Expanded Heat Exchanger for Absorption Chilling
(The American Society of Mechanical Engineers (ASME), 2025)The increasing demand for energy-efficient and environmentally friendly cooling technologies has driven the exploration of advanced heat exchanger (HX) designs. Traditional metal HXs, while effective, are often heavy, ... -
Temperature Uniformity Analysis of a Cooling Plate With Stepped Trapezoidal Fins Applied to Boiling Battery Thermal Management System
(The American Society of Mechanical Engineers (ASME), 2025)- -
Numerical Study on the Effect of Surface Wettability on Heat Transfer Characteristics of High-Temperature Two-Phase Closed Thermosiphon
(The American Society of Mechanical Engineers (ASME), 2025)- -
Design and Manufacturing of a Novel Vacuumed Hybrid Cooler for the Central Process Unit: Performance Comparison and Optimization
(The American Society of Mechanical Engineers (ASME), 2025)- -
Exergoeconomic Analysis and Optimization of a Combined Cooling, Heating, and Power System Based on a Super-Trans-Subcritical Regenerative Cycle Using the Liquefied Natural Gas Cold Energy and Steam Methane Reforming Waste Heat
(The American Society of Mechanical Engineers (ASME), 2025)This article designs and analyzes a combined cooling, heating, and power system based on the step utilizing liquefied natural gas cold energy and steam methane reforming flue gas waste heat. The system performance is ... -
Numerical Analysis of the Thermal Performance in a Five-by-Five Battery Pack Configured With the Phase Change Material and Optimized Fin Layout
(The American Society of Mechanical Engineers (ASME), 2025)Batteries employed in electric vehicles are important components due to their significant high heat capacity and energy density characteristics. However, these batteries experience drastic temperature rise due to the high ... -
Effect of Swirl Blade Deflection Angle on Combustion and Emission Characteristics of By-Product Gas Boiler
(The American Society of Mechanical Engineers (ASME), 2025)Swirl burner is widely used in boilers due to its high combustion efficiency. The swirl blade deflection angle affects the combustion and emission characteristics of the boiler. In this study, based on the experimental ... -
Heat Transfer Coefficients and Film Cooling Effectiveness on the Endwall of a Transonic Turbine Vane Measured With the Reference Luminophore of Binary Pressure-Sensitive Paint
(The American Society of Mechanical Engineers (ASME), 2025)Film cooling is a key technique used to reduce heat transfer from hot combustion gases to stationary and rotating components in a gas turbine engine. In high-performance engines, the endwall experiences high heat gains due ... -
Nanofluid-Based Counterflow Immersion Cooling for Lithium-Ion Battery During Fast Charging
(The American Society of Mechanical Engineers (ASME), 2025)Immersion cooling technology holds significant potential for Lithium-ion battery thermal management. This paper proposes a counterflow-based battery thermal management system (BTMS) under fast charging conditions, using a ... -
Thermodynamic Analysis of Vapor Compression Refrigeration System Using Domestic Liquefied Petroleum Gas as Refrigerant
(The American Society of Mechanical Engineers (ASME), 2025)A thermodynamic study was performed on a vapor compression refrigeration system (VCRS) with domestic liquefied petroleum gas (LPG) as a refrigerant. LPG's coefficient of performance, power consumption, and refrigeration ... -
Simulation of External Environment of Air-Source Heat Pump Cluster Group for Cold Area Heating
(The American Society of Mechanical Engineers (ASME), 2025)As an efficient and clean heating technology, air-source heat pumps have been widely used in central heating in North China. A numerical simulation model of an air-source heat pump cluster was established, and the influence ... -
Effects of Nanoparticle Deposition on the Flow Boiling Characteristics of a MWCNT Nanofluid
(The American Society of Mechanical Engineers (ASME), 2025)In this study, highly conductive nanoparticles, known for their superior heat transfer enhancement in bulk domains, were incorporated into three-dimensional nanofluids containing multiwalled carbon nanotubes (MWCNTs). This ... -
Aero-Thermal Calculations for a Rotor Blade With Different Dimple and Protrusion Arrangements
(The American Society of Mechanical Engineers (ASME), 2025)This article presents an investigation of dimples and protrusions arranged on the end wall of a rotor blade to enhance heat transfer. This study explores three arrangements of dimples and protrusions relative to the pin-fins, ...