Browsing Journal of Manufacturing Science and Engineering by Issue Date
Now showing items 1-20 of 7598
-
A Novel, Image-Based Method for Characterization of the Porosity of Additively Manufactured Bone Scaffolds With Complex Microstructures
(The American Society of Mechanical Engineers (ASME), 1/19/2023 )Bone tissue engineering has emerged as a promising strategy for the treatment of osseous fractures, defects, and ultimately diseases caused by, for example, bone tumor resection, accident trauma, and congenital malformation. ... -
Flaw Detection in Multi-Laser Powder Bed Fusion Using In Situ Coaxial Multi-Spectral Sensing and Deep Learning
(The American Society of Mechanical Engineers (ASME), 1/19/2023 )Multi-laser powder bed fusion (M-LPBF) systems are garnering increased attention in metal additive manufacturing as they promise increased productivity and part size without sacrificing feature resolution or mechanical ... -
A Voxel-Based End Milling Simulation Method to Analyze the Elastic Deformation of a Workpiece
(The American Society of Mechanical Engineers (ASME), 10/13/2022)A new method to analyze the elastic deformation of a workpiece during end milling is proposed. One of the advantages of this method is the possibility of easily combining it with a voxel-based milling simulation, which is ... -
In-Space Additive Manufacturing: A Review
(The American Society of Mechanical Engineers (ASME), 11/3/2022 )Manufacturing or repairing parts on-site, high geometric freedom, and feedstock efficiency have long been regarded as nascent capabilities of additive manufacturing (AM) technologies. Researchers aim to adopt these ... -
Mist Flow in Through-Tool Minimum Quantity Lubrication Drilling: Two-Phase Flow Simulation and Experimental Observation
(The American Society of Mechanical Engineers (ASME), 11/30/2022)Through-tool minimum quantity lubrication (MQL) drilling has been used in industry for decades, but little information is available on the coolant channel design and the effect on fluid distribution due to the inability ... -
Improving Structural Integrity of Direct Laser-Deposited Ni–Co–Cr–Al–Y Superalloys by Alloy Modification
(The American Society of Mechanical Engineers (ASME), 11/7/2022 )Ni- and Co-based M–Cr–Al–Y (M = Ni and/or Co), dual phase β and γ/γ′, β—Ni–Al, γ—Ni(Co, Cr), and γ′—Ni3–Al superalloys exhibit several beneficial high-temperature (>1000 °C) (2012 °F) strength and corrosion resistance ... -
Three-Dimensional Printing of Highly Conducting PEDOT: PSS-Based Polymers
(The American Society of Mechanical Engineers (ASME), 11/7/2022 )Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) is one of the most successful conducting polymers for electronic applications. Most commonly, the spin coating process is used to fabricate PEDOT:PSS ... -
A Simulation Study on the Effect of Layer Thickness Variation in Selective Laser Melting
(The American Society of Mechanical Engineers (ASME), 11/7/2022 )Selective laser melting (SLM) has gained prominence in the manufacturing industry for its ability to produce lightweight components. As the raw material used is in powder form, the stochastic nature of the powder distribution ... -
Controlling Damage Evolution in Geometrically Identical Cold Forged Parts by Counterpressure
(The American Society of Mechanical Engineers (ASME), 12/1/2022 )It is investigated to what extent the evolution of ductile damage in cold forging can be controlled without changing the geometry of the produced part. Besides the effects of strain hardening and residual stresses, damage, ... -
Special Issue: Manufacturing Science Engineering Conference 2022
(The American Society of Mechanical Engineers (ASME), 12/1/2022 )The 17th ASME International Manufacturing Science and Engineering Conference (MSEC 2022), sponsored by the Manufacturing Engineering Division (MED) of ASME, was held from June 27, 2022 to July 1, 2022, in West Lafayette, ... -
Hierarchical Porous Structure Fabrication Via Hybrid Stereolithography and Inkjet Printing With Sacrificial Liquid
(The American Society of Mechanical Engineers (ASME), 12/1/2022 )Inspired by porous morphology in nature, such as bone and lung tissues, synthetic porous materials are widely adopted in engineering applications that require lightweight, thermal resistance, energy absorption, and structural ... -
Development of Novel Low-Cost Sustainable Abrasive Flow Finishing Media From Ground Tire Rubber and Its Performance Evaluation
(The American Society of Mechanical Engineers (ASME), 12/12/2022)The present experimental endeavor aims to develop and study the characteristics of a novel ground tire rubber media (GTRM) through rheological, thermal, and mechanical characterizations. Thermogravimetric analysis reveals ... -
A Deformation Control Method in Thin-Walled Parts Machining Based on Force and Stiffness Matching Via Cutter Orientation Optimization
(The American Society of Mechanical Engineers (ASME), 12/2/2022 )In the milling process, significant machining errors may occur due to the low stiffness of thin-walled parts. To reduce the cutting force-induced deformation in milling thin-walled parts such as blades, a cutter orientation ... -
Editorial
(The American Society of Mechanical Engineers (ASME), 12/23/2022)I am honored to serve our manufacturing community as the Editor-in-Chief of the Journal of Manufacturing Science and Engineering (JMSE). JMSE is a historical journal and is thriving. In July 2022, JMSE has the highest ... -
Predictive Thermal Modeling and Characterization of Ultrasonic Consolidation Process for Thermoplastic Composites
(The American Society of Mechanical Engineers (ASME), 12/5/2022 )Ultrasonic consolidation (USC) of thermoplastic composites is a highly attractive and promising method to manufacture high-performance composites. This work focuses on USC of dry carbon fiber (CF) fabrics with high-temperature ... -
Tire Testing
(The American Society of Mechanical Engineers (ASME), 1960)The use of tire tests for fiber characterization in research programs aimed at the development of improved tire yarns is discussed. Examples are included to demonstrate some of the factors ... -
Nomographic Synthesis of Generator Linkages
(The American Society of Mechanical Engineers (ASME), 1960)Machines are doing more complex jobs; the need grows for simple operation and low cost of parts. The generator, or computer, linkage often fills this bill if technical requirements can be met ... -
Edge Influence Coefficients for Toroidal Shells of Negative Gaussian Curvature
(The American Society of Mechanical Engineers (ASME), 1960)Continuing the work presented in reference [1], the present paper gives additional tables for the edge deformations of constant-thickness toroidal shells subject to edge bending loads and uniform ... -
A Quantitative Investigation of the Factors Which Influence the Fatigue Life of a V-Belt
(The American Society of Mechanical Engineers (ASME), 1960)A new design method for V-belts has been developed. The new method involves a horsepower-life relationship which has been derived on the basis of the results of a vast experimental program ... -
Discussion: “A Photoelastic Analysis of Machining Stresses” (Usui, E., and Takeyama, H., 1960, ASME J. Eng. Ind., 82, pp. 303–307)
(The American Society of Mechanical Engineers (ASME), 1960)