Infrared Visualization of the Cavity Effect Using Origami Inspired SurfacesSource: Journal of Heat Transfer:;2016:;volume( 138 ):;issue: 002::page 20901DOI: 10.1115/1.4032229Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: Surface temperature and apparent radiative surface properties (emissivity, absorptivity) may be controlled by varying surface topology through a phenomenon known as the cavity effect. Cavities created by origami folds offer the potential to achieve dynamic control of apparent radiative surface properties through actuation. To illustrate this phenomenon, a thin (0.0254 mm) stainlesssteel, specularly reflecting surface (emissivity, خµ = 0.117) was resistively heated (6.74 W). Accordionshaped folds (1.27 cm panels) were used to create Vshaped grooves that transition from 29آ° at the center to 180آ° near the edges. Thermocouples were attached to the center of each cavity panel (Figure (a)). An IR image of the surface (Figure (b)) reveals that the apparent temperature increases as the cavity angle decreases and is not necessarily indicative of the actual surface temperature. This increase is due to an increase in the number of specular reflections associated with the cavity effect. A similar folded surface was placed 7 cm from a blackbody radiator at 1000آ° C, to illustrate the change in apparent absorptivity with cavity angle. The cavity angle was held constant across the surface and varied between tests from 180آ° to 37آ° (Figure (c), top to bottom). The increase in apparent temperature is a direct result of the increase in apparent absorptivity for decreasing cavity angle, despite constant heating conditions.
|
Collections
Show full item record
contributor author | Blanc, Mitchell J. | |
contributor author | Mulford, Rydge B. | |
contributor author | Jones, Matthew R. | |
contributor author | Iverson, Brian D. | |
date accessioned | 2017-05-09T01:30:11Z | |
date available | 2017-05-09T01:30:11Z | |
date issued | 2016 | |
identifier issn | 0022-1481 | |
identifier other | ht_138_02_020901.pdf | |
identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/161543 | |
description abstract | Surface temperature and apparent radiative surface properties (emissivity, absorptivity) may be controlled by varying surface topology through a phenomenon known as the cavity effect. Cavities created by origami folds offer the potential to achieve dynamic control of apparent radiative surface properties through actuation. To illustrate this phenomenon, a thin (0.0254 mm) stainlesssteel, specularly reflecting surface (emissivity, خµ = 0.117) was resistively heated (6.74 W). Accordionshaped folds (1.27 cm panels) were used to create Vshaped grooves that transition from 29آ° at the center to 180آ° near the edges. Thermocouples were attached to the center of each cavity panel (Figure (a)). An IR image of the surface (Figure (b)) reveals that the apparent temperature increases as the cavity angle decreases and is not necessarily indicative of the actual surface temperature. This increase is due to an increase in the number of specular reflections associated with the cavity effect. A similar folded surface was placed 7 cm from a blackbody radiator at 1000آ° C, to illustrate the change in apparent absorptivity with cavity angle. The cavity angle was held constant across the surface and varied between tests from 180آ° to 37آ° (Figure (c), top to bottom). The increase in apparent temperature is a direct result of the increase in apparent absorptivity for decreasing cavity angle, despite constant heating conditions. | |
publisher | The American Society of Mechanical Engineers (ASME) | |
title | Infrared Visualization of the Cavity Effect Using Origami Inspired Surfaces | |
type | Journal Paper | |
journal volume | 138 | |
journal issue | 2 | |
journal title | Journal of Heat Transfer | |
identifier doi | 10.1115/1.4032229 | |
journal fristpage | 20901 | |
journal lastpage | 20901 | |
identifier eissn | 1528-8943 | |
tree | Journal of Heat Transfer:;2016:;volume( 138 ):;issue: 002 | |
contenttype | Fulltext |