Journal of Fluids Engineering: Recent submissions
Now showing items 8361-8380 of 9024
-
Some Thoughts on Journal Publication Trends
(The American Society of Mechanical Engineers (ASME), 1978) -
Calculation of Two-Phase Dispersed Droplet-In-Vapor Flows Including Normal Shock Waves
(The American Society of Mechanical Engineers (ASME), 1978)A method for calculating quasi-one-dimensional, steady-state, two-phase dispersed droplet-in-vapor flow has been developed. The technique is applicable to both subsonic and supersonic single component ... -
Laminar Shear Layer Due to a Thin Flat Plate Oscillating With Zero Mean Velocity
(The American Society of Mechanical Engineers (ASME), 1978)A numerical solution of the unsteady laminar boundary layer equations is described for the flow due to a semi-infinite plate, sinusoidally oscillating with zero mean velocity. The plate periodically ... -
Discussion: “Frictional Moment of Flow Between Two Concentric Spheres, One of Which Rotates” (Nakabayashi, K., 1978, ASME J. Fluids Eng., 100, pp. 97–106)
(The American Society of Mechanical Engineers (ASME), 1978) -
Fluid Lubrication Theory of Roller Bearing—Part I: Fluid Lubrication Theory for Two Rotating Cylinders in Contact
(The American Society of Mechanical Engineers (ASME), 1962)This paper which consists of Parts I and II presents a general and practical fluid lubrication theory of roller bearings lubricated by Newtonian and non-Newtonian lubricants with considerations ... -
Turbulence Characteristics of the Flow Downstream of a Symmetric, Plane Sudden Expansion
(The American Society of Mechanical Engineers (ASME), 1978) -
Cold Flow Tests of a Bluff-Body Flame Stabilizer
(The American Society of Mechanical Engineers (ASME), 1978)The aerodynamic characteristics of separated, recirculating flows behind a two-dimensional nozzle and bluff-body combination, which modeled a lean mixture combustor, was explored by a series of ... -
On the Growth of Steam Droplets Formed in a Laval Nozzle Using Both Static Pressure and Light Scattering Measurements
(The American Society of Mechanical Engineers (ASME), 1978)A series of experiments on steam condensation have been made in a Laval nozzle over a variety of starting conditions such that the onset of condensation occurs in the range −40 to 40°C ... -
Experimental Study of a Solid-Gas Jet Issuing Into a Transverse Stream
(The American Society of Mechanical Engineers (ASME), 1978)The results of an experimental investigation of the trajectory and dispersion of a solid-gas (silicate-air) jet injected into a transverse stream are presented. The centerline and the spread of ... -
Vortex Sheet Analysis of the Giromill
(The American Society of Mechanical Engineers (ASME), 1978)A two-dimensional analysis of the performance and flowfield of the Giromill is presented. The Giromill is a vertical-axis wind turbine with straight blades that are articulated to produce maximum ... -
Analytical and Experimental Study of Externally Pressurized Air Lubricated Journal Bearings
(The American Society of Mechanical Engineers (ASME), 1962)A simplified analysis for calculating the characteristics, such as stiffness, flow, and load of an externally pressurized gas journal bearing, is obtained through a standard one-dimensional flow ... -
A Novel Physico-Computational Model for Quasi One-Dimensional Gas-Particle Flows
(The American Society of Mechanical Engineers (ASME), 1978)The analysis of gas-particle flows is complicated by the need to account for momentum and energy coupling between phases. The concept of regarding the particle phase as a source of momentum ... -
The Velocity Characteristics of Ventilated Rooms
(The American Society of Mechanical Engineers (ASME), 1978)Measured and calculated values of the velocity characteristics of a modeled room with ventilation arrangements are reported. The measurements were obtained by laser-Doppler anemometry and the ... -
On the Translatory Whirl Motion of a Vertical Rotor in Plain Cylindrical Gas-Dynamic Journal Bearings
(The American Society of Mechanical Engineers (ASME), 1962)For the theoretical prediction of the dynamical characteristics of a rotor system, it is necessary to have an accurate knowledge of the bearing fluid film forces under dynamical conditions. ... -
Laminar-Turbulent Flow in a Spherical Annulus
(The American Society of Mechanical Engineers (ASME), 1978)Experimental results are presented regarding the nature of the flow of a viscous incompressible fluid contained between two concentric spherical surfaces that rotate at different angular velocities. ... -
Analytical and Experimental Studies of ASME Flow Nozzles
(The American Society of Mechanical Engineers (ASME), 1978)In this paper, we first present a state of the art review of the published work concerning theoretical nozzle discharge coefficients. Then, we develop a new nozzle discharge coefficient based ... -
Loss Characteristics of Orifices and Nozzles
(The American Society of Mechanical Engineers (ASME), 1978)Loss characteristics of sharp-edged orifices, quadrant-edged orifices for varying edge radii, and nozzles are studied for Reynolds numbers less than 10,000 for β ratios from 0.2 to 0.8. The ... -
Discussion: “The Effect of Taylor Vortex Flow on the Radial Forces in an Annulus Having Variable Eccentricity and Axial Flow” (Coney, J. E., and Atkinson, J., 1978, ASME J. Fluids Eng., 100, pp. 210–214)
(The American Society of Mechanical Engineers (ASME), 1978) -
Tailoring the Waveform of a Periodic Flow With a Programmable Damper
(The American Society of Mechanical Engineers (ASME), 1978)Investigators of unsteady flows normally have little control over the waveform of the flow unsteadiness. This paper describes a programmable rotating blade damper system that is capable of ... -
Leading-Edge Correction for the Supercavitating Flat-Plate Hydrofoil
(The American Society of Mechanical Engineers (ASME), 1978)A leading-edge correction is obtained via the method of matched asymptotic expansions to the first-order linearized solution for the potential flow past a supercavitating flat-plate hydrofoil at ...