Journal of Fluids Engineering: Recent submissions
Now showing items 8381-8400 of 9024
-
Discussion: “Experimental Study of a Solid-Gas Jet Issuing Into a Transverse Stream” (Salzman, R. N., and Schwartz, S. H., 1978, ASME J. Fluids Eng., 100, pp. 333–338)
(The American Society of Mechanical Engineers (ASME), 1978) -
Discussion: “A Procedure for Computation of Fully Stalled Flows in Two-Dimensional Passages” (Woolley, R. L., and Kline, S. J., 1978, ASME J. Fluids Eng., 100, pp. 180–186)
(The American Society of Mechanical Engineers (ASME), 1978) -
Effect of Polymer Additives on Cavitation Development and Noise in Water Flow Through an Orifice
(The American Society of Mechanical Engineers (ASME), 1978)The cavitation behavior and the shock pressure were experimentally investigated in dilute aqueous solutions of polymer flowing through an orifice, and the following facts were observed: (i) Very ... -
Discussion: “Developing Region of Laminar Jets With Uniform Exit Velocity Profiles” (Rankin, G. W., and Sridhar, K., 1978, ASME J. Fluids Eng., 100, pp. 55–59)
(The American Society of Mechanical Engineers (ASME), 1978) -
Discussion: “Analytical and Experimental Studies of ASME Flow Nozzles” (Benedict, R. P., and Wyler, J. S., 1978, ASME J. Fluids Eng., 100, pp. 265–274)
(The American Society of Mechanical Engineers (ASME), 1978) -
Discussion: “Reynolds Number Dependence of Skin Friction and Other Bulk Flow Variables in Two-Dimensional Rectangular Duct Flow” (Dean, R. B., 1978, ASME J. Fluids Eng., 100, pp. 215–223)
(The American Society of Mechanical Engineers (ASME), 1978) -
Discussion: “Turbulence Measurements in Boundary Layers Along Mildly Curved Surfaces” (Shivaprasad, B. G., and Ramaprian, B. R., 1978, ASME J. Fluids Eng., 100, pp. 37–46)
(The American Society of Mechanical Engineers (ASME), 1978) -
Discussion: “Leading-Edge Correction for the Supercavitating Flat-Plate Hydrofoil” (Plotkin, Allen, 1978, ASME J. Fluids Eng., 100, pp. 276–280)
(The American Society of Mechanical Engineers (ASME), 1978) -
Spectral and Probability-Density Nature of Square-Prism Separation-Reattachment Wall Pressures
(The American Society of Mechanical Engineers (ASME), 1978)The statistical nature of the fluctuating pressures associated with the separation-reattachment flow were studied for a two-dimensional square prism in uniform flow for low (0.33 percent) and ... -
Influence of Volute Surface Roughness on the Performance of a Centrifugal Pump
(The American Society of Mechanical Engineers (ASME), 1978) -
Particle Deposition in a Charged Aerosol Flowing Through a Conducting Tube
(The American Society of Mechanical Engineers (ASME), 1978)A mathematical analysis is presented for charged aerosol flowing in an infinitely long, cylindrical, conducting tube. The aerosol is assumed to move in “plug” flow and to be dilute, unipolar, ... -
Gas Flow Through Cracks
(The American Society of Mechanical Engineers (ASME), 1978)Nitrogen flow through 13 idealized cracks has been measured and compared with theoretical predictions. Gas conditions covered upstream pressure and temperature ranges of between 10 and 50 bars ... -
Symmetric Sink Flow Between Parallel Plates
(The American Society of Mechanical Engineers (ASME), 1978)Steady, laminar, incompressible flow converging radially between two stationary disks is investigated numerically as a continuously developing flow problem under the internal boundary layer ... -
Analysis of Bearings Operating in Turbulent Regime
(The American Society of Mechanical Engineers (ASME), 1962)Proceeding from the results obtained previously [5] this paper analyzes theoretically the three-dimensional motion in the lubricant layer by using Prandtl’s mixing length theory. Formulas and ... -
A Wind-Tunnel Study of the Effect of Turning Vanes on the Aerodynamic Drag of Tractor-Trailer Trucks
(The American Society of Mechanical Engineers (ASME), 1978)A Wind-Tunnel Study was made of the reduction of the aerodynamic drag of tractor-trailer trucks due to turning vanes used to control flow separation. A variety of vane settings and positions ... -
First-Order Pump Surge Behavior
(The American Society of Mechanical Engineers (ASME), 1978)This paper presents the results of an empirical study undertaken to assess the appropriateness and applicability of a simple, analytical model of pump-piping system flow instability. The analysis ... -
A Numerical Study of the Laminar Viscous Incompressible Flow Through a Pipe Orifice
(The American Society of Mechanical Engineers (ASME), 1978)The present paper discusses a numerical algorithm for the solution of the steady flow of a viscous fluid through a pipe orifice which allows for considerable flexibility in the choice of ... -
A Study of the Base Drag of Tractor-Trailer Trucks
(The American Society of Mechanical Engineers (ASME), 1978)Measurements were made of the base pressure distribution and the aerodynamic drag of a variety of 1/8th-scale tractor-trailer truck models in a wind tunnel at yaw angles ranging from 0° ... -
Investigation of Whirl in Externally Pressurized Air-Lubricated Journal Bearings
(The American Society of Mechanical Engineers (ASME), 1962)The nature of whirl of a rigid rotor in externally pressurized air-lubricated journal bearings, including self-acting bearings as a special case, is discussed and an experimental investigation ... -
Prediction of Incompressible Turbulent Separating Flow
(The American Society of Mechanical Engineers (ASME), 1978)The predictions of several turbulence models are compared with experimental data for flows containing regions of recirculation using an inverse finite-difference method to solve the boundary layer ...