Journal of Fluids Engineering: Recent submissions
Now showing items 7781-7800 of 9024
-
Laminar Boundary Layer Near the Rotating End Wall of a Confined Vortex
(The American Society of Mechanical Engineers (ASME), 1982)The results of an experimental and theoretical investigation of the fluid mechanics in a confined vortex are discussed with particular emphasis on behavior away from the axis of symmetry and ... -
On the Analysis of Turbulent Boundary Layers on Slender Cylinders
(The American Society of Mechanical Engineers (ASME), 1982)An earlier analysis of turbulent flow along a cylinder in a uniform stream by White is corrected. The analysis has been extended to include turbulent flow along a cylinder extruding through ... -
A Self-Correcting and Self-Checking Gas Turbine Meter
(The American Society of Mechanical Engineers (ASME), 1982)A new metering concept of a self-correcting and self-checking turbine meter is described in which a sensor rotor downstream from the main rotor senses and responds to changes in the exit angle ... -
Practical Experiences with Flow-Induced Vibrations
(The American Society of Mechanical Engineers (ASME), 1982) -
Review—Theoretical Models of Gas-Liquid Flows
(The American Society of Mechanical Engineers (ASME), 1982)Two-phase flow is an “insecure” science. Many factors influence the phenomena, limiting the value of theory unless supported and guided by observation. Several methods of analysis are available; ... -
Discussion: “Contributions to the Theory of Single-Sample Uncertainty Analysis” (Moffat, R. J., 1982, ASME J. Fluids Eng., 104, pp. 250–258)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “A New Instrument in Cavitation Research: The Cavitation Susceptibility Meter” (Oldenziel, D. M., 1982, ASME J. Fluids Eng., 104, pp. 136–141)
(The American Society of Mechanical Engineers (ASME), 1982) -
Review—Combined Measurements of Particle Velocities, Size Distributions, and Concentrations
(The American Society of Mechanical Engineers (ASME), 1982)The present paper describes combined laser Doppler particle sizing systems which permit simultaneous velocity and size measurements of individual particles. Combined measurements of these properties ... -
Hydrodynamic Lubrication of Narrow Press-Fitted Porous Metal Bearings
(The American Society of Mechanical Engineers (ASME), 1963)An analysis is made of the performance of narrow porous metal bearings (e.g., sintered bronze powder) which operate with a full film of lubricant. The configuration considered is that in which ... -
The Magnetohydrodynamic Finite Step Slider Bearing
(The American Society of Mechanical Engineers (ASME), 1963)A theoretical analysis is made of the finite step slider bearing using an electrically conducting liquid metal lubricant in the presence of a magnetic field applied both tangentially and ... -
Review—Numerical Models for Dilute Gas-Particle Flows
(The American Society of Mechanical Engineers (ASME), 1982)The rapidly increasing capability of computers has led to the development of numerical models for gaseous flows and, in turn, gas-particle and gas-droplet flows. This paper reviews the essential ... -
Discussion: “Equilibrium Parameters for Two-Dimensional Turbulent Wakes” (Sreenivasan, K. R., and Narasimha, R., 1982, ASME J. Fluids Eng., 104, pp. 167–169)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Calculation of Annular and Twin Parallel Jets Using Various Discritization Schemes and Turbulence-Model Variations” (Leschziner, M. A., and Rodi, W., 1981, ASME J. Fluids Eng., 103, pp. 352–360)
(The American Society of Mechanical Engineers (ASME), 1982) -
Spreading Rate and Reattachment of Coaxial Jets of High Mean-Velocity Ratio
(The American Society of Mechanical Engineers (ASME), 1982) -
A Study of Shock Waves in Three-Dimensional Transonic Flow
(The American Society of Mechanical Engineers (ASME), 1982)Although a number of inviscid numerical methods have been developed for the calculation of three-dimensional transonic flow in turbomachinery blade passages it is often difficult to compare the ... -
Discussion: “Numerical Solution for Laminar Two Dimensional Flow About a Cylinder Oscillating in a Uniform Stream” (Hurlbut, S. E., Spaulding, M. L., and White, F. M., 1982, ASME J. Fluids Eng., 104, pp. 214–220)
(The American Society of Mechanical Engineers (ASME), 1982) -
Drag-Characterization Method for Arbitrarily Rough Surfaces by Means of Rotating Disks
(The American Society of Mechanical Engineers (ASME), 1982)An indirect similarity-law characterization method is presented for any arbitrary irregular roughness covering a circular disk. Formulas are presented for converting the measured torques and rotary ... -
Fluid Structure Interaction in Piping by Component Synthesis
(The American Society of Mechanical Engineers (ASME), 1982)Pipe vibrations can be induced by internal liquid pulsations which propagate throughout the piping system and create unbalanced oscillatory pressure forces at locations where either flow area or ... -
Curved Ducts With Strong Secondary Motion: Velocity Measurements of Developing Laminar and Turbulent Flow
(The American Society of Mechanical Engineers (ASME), 1982)Two orthogonal components of velocity and associated Reynolds stresses have been measured in a square-sectioned, 90 degree bend of 2.3 radius ratio using laser-Doppler velocimetry for Reynolds ... -
Fatigue Crack Propagation and Applied Stress Range—An Energy Approach
(The American Society of Mechanical Engineers (ASME), 1963)Using the saturation of hysteresis energy absorption as a criterion for fatigue crack propagation, the rate of crack propagation in a thin and wide metal sheet under repeated axial loading is ...