Journal of Fluids Engineering: Recent submissions
Now showing items 7761-7780 of 9024
-
Compressor Stability Analysis
(The American Society of Mechanical Engineers (ASME), 1982)A Dynamic Compressor Analysis (DCA) applicable to axial flow compressors operating with a wide variety of inlet or exhaust conditions (steady-state or dynamic, and with total pressure and/or ... -
Impulsively-Started Flow About Four Types of Bluff Body
(The American Society of Mechanical Engineers (ASME), 1982)Measurement of the forces acting on a circular cylinder and those on three other noncircular cylinders is reported. The results confirm and quantify the profound effects of the shedding of the ... -
Flow Behind Two Coaxial Circular Cylinders
(The American Society of Mechanical Engineers (ASME), 1982)The flow behind two circular cylinders of different diameters, which were joined coaxially has been examined at the Reynolds number of 8 × 104 . The detailed pressure spectral measurements ... -
Contributions to the Theory of Single-Sample Uncertainty Analysis
(The American Society of Mechanical Engineers (ASME), 1982) -
Measurements in a Motored Four-Stroke Reciprocating Model Engine
(The American Society of Mechanical Engineers (ASME), 1982)Measurements of ensemble-averaged axial and swirl velocities and the rms of the corresponding fluctuations obtained by laser-Doppler anemometry, are reported for the axisymmetric swirling flow in ... -
Discussion: “Transient Characteristics of a Centrifugal Pump During Starting Period” (Tsukamoto, H., and Ohashi, H., 1982, ASME J. Fluids Eng., 104, pp. 6–13)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Transverse Oscillations of a Vertical Pile in Waves” (Angrilli, F., and Cossalter, V., 1982, ASME J. Fluids Eng., 104, pp. 46–52)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Flow in a Pipe Following an Abrupt Increase in Surface Roughness” (Logan, Jr., Earl, and Jones, J. B., 1963, ASME J. Basic Eng., 85, pp. 35–38)
(The American Society of Mechanical Engineers (ASME), 1963) -
Internal Fluid Flow: The Fluid Dynamics of Flow on Pipes and Ducts and Fundamentals of Pipe Flow
(The American Society of Mechanical Engineers (ASME), 1982) -
Evaluation of a Wall-Flow Direction Probe for Measurements in Separated Flows
(The American Society of Mechanical Engineers (ASME), 1982)The upstream-downstream flow direction intermittency γpu is an important parameter that can quantitatively describe the stages of flow separation. This paper gives an improved design for a ... -
Plug Flow of Coarse Particles in a Horizontal Pipe
(The American Society of Mechanical Engineers (ASME), 1982)Plug flow of coarse particles was investigated experimentally in a horizontal pipe, in which a sub-pipe for secondary air injection was installed. Measurements were made about the plug motion, ... -
Discussion: “Cavitation Inception in Pumps” (Mc Nulty, P. J., and Pearsall, I. S., 1982, ASME J. Fluids Eng., 104, pp. 99–104)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Visual Cavitation Studies of Mixed Flow Pump Impellers” (Wood, G. M., 1963, ASME J. Basic Eng., 85, pp. 17–28)
(The American Society of Mechanical Engineers (ASME), 1963) -
Direct Force Wall Shear Measurements in Pressure-Driven Three-Dimensional Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1982)Unique, simultaneous direct measurements of the magnitude and direction of the local wall shear stress in a pressure-driven three-dimensional turbulent boundary layer are presented. The flow is ... -
Discussion: “A Flow Model for the Effect of a Slanted Base on Drag” (Sedney, R., 1982, ASME J. Fluids Eng., 104, p. 54)
(The American Society of Mechanical Engineers (ASME), 1982) -
On the Scaling of Impulsively Started Incompressible Turbulent Round Jets
(The American Society of Mechanical Engineers (ASME), 1982)A scaling law for transient, turbulent, incompressible, round jets is reported. Numerical solutions of the Navier-Stokes equations were obtained using a k-ε model for turbulence. The constants ... -
Equilibrium Parameters for Two-Dimensional Turbulent Wakes
(The American Society of Mechanical Engineers (ASME), 1982)The parameters characterizing a plane turbulent wake in its equilibrium state of development are determined through careful experiment and analysis. -
Preston Tube Calibrations and Direct Force Floating Element Measurements in a Two-Dimensional Turbulent Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1982)Preston tubes provide a convenient means of estimating local wall shear stress. Practical difficulties arise from a lack of calibration data obtained in turbulent boundary layer flows and from ... -
A New Instrument in Cavitation Research: The Cavitation Susceptibility Meter
(The American Society of Mechanical Engineers (ASME), 1982)The rate of cavitation in liquid flow appears to be linked to the concentration and size distribution of gas bubbles and “weak” nuclei in the liquid used, as well as to the dissolved gas ... -
Scaling Parameters for a Time-Averaged Separation Bubble
(The American Society of Mechanical Engineers (ASME), 1982)A splitter plate is placed in the wake of a two-dimensional bluff body. The splitter plate is long enough for the separated flow behind the body to reattach on the splitter plate. The ...