Journal of Fluids Engineering: Recent submissions
Now showing items 7741-7760 of 9024
-
Draining of Tanks With Submerged Outlets or Without Vacuum-Relief
(The American Society of Mechanical Engineers (ASME), 1982)It is shown that the gravity-induced draining of liquid from a tank does not cease when the pressure differential at the outlet is zero if the liquid level is still above the outlet. Instead, ... -
The Effects of Roughness and Shear on Vortex Shedding Cell Lengths Behind a Circular Cylinder
(The American Society of Mechanical Engineers (ASME), 1982)Circular cylinders of aspect ratio L/D=17 were tested in a wind tunnel under a wide range of spanwise upstream velocity shears. The correlation between upstream shear, characterized by a ... -
Scaling Laws for Metering the Flow of Gas-Particle Suspensions Through Venturis
(The American Society of Mechanical Engineers (ASME), 1982)An experimental investigation was undertaken to determine those scaling parameters applicable to measuring the mass flow rate of gas-particle suspensions through venturis. It was found that Stokes ... -
Oil Thickness Variation on Wavy Water in the Presence of Wind
(The American Society of Mechanical Engineers (ASME), 1982)The effect of the wind on the distribution of an oil layer on wavy water has been examined analytically and the results are compared with experimental values. It is found that the wind tends ... -
Discussion: “Flow in the Entrance of a Tube” (Campbell, William D., and Slattery, John C., 1963, ASME J. Basic Eng., 85, pp. 41–45)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Complete Velocity Profile and ‘Optimum’ Skin Friction Formulas for the Plane Wall-Jet” (Hammond, G. P., 1982, ASME J. Fluids Eng., 104, pp. 59–65)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “The Onset of Bubble-Ring Cavitation on Hemispherical Headforms” (Parkin, B. R., 1982, ASME J. Fluids Eng., 104, pp. 115–122)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Optimum Strut-Configuration for Downstream Annular Diffusers With Variable Swirling Inlet Flow” (Senoo, Y., Kawaguchi, N., Kojima, T., and Nishi, M., 1981, ASME J. Fluids Eng., 103, pp. 294–298)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Initial Region of Subsonic Coaxial Jets of High Mean-Velocity Ratio” (Ko, N. W. M., and Au, H., 1981, ASME J. Fluids Eng., 103, pp. 335–338)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Combined Simultaneous Flow Visualization—Hot-Wire Anemometry for the Study of Turbulent Flows” (Falco, R. E., 1980, ASME J. Fluids Eng., 102, p. 174)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “A Four Hole Pressure Probe for Fluid Flow Measurements in Three Dimensions” (Shepherd, I. C., 1981, ASME J. Fluids Eng., 103, pp. 590–594)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Drag Reducing Polymer in Helicoidal Flow” (Kuo, J. T., and Kovasznay, L. S. G., 1981, ASME J. Fluids Eng., 103, pp. 491–496)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Generation of Oscillating Jets” (Favre-Marinet, M., Binder, G., and Hac, Te. V., 1981, ASME J. Fluids Eng., 103, pp. 609–614)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Cavitation Inception in Spool Valves” (Martin, C. Samuel, Medlarz, H., Wiggert, D. C., and Brennen, C., 1981, ASME J. Fluids Eng., 103, pp. 564–576)
(The American Society of Mechanical Engineers (ASME), 1982) -
Transient Characteristics of a Centrifugal Pump During Starting Period
(The American Society of Mechanical Engineers (ASME), 1982)A theoretical and experimental study has been made on the transient characteristics of a centrifugal pump during its rapid acceleration from standstill to final speed. Instantaneous rotatinal ... -
Sizing Criteria for Laser Anemometry Particles
(The American Society of Mechanical Engineers (ASME), 1982) -
An Experiment Concerning the Confluence of a Wake and a Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1982)Measurements have been performed at low speed in the confluent region of a two dimensional wake and turbulent boundary layer. A tandem symmetrical arrangement was used, placed in a variable ... -
Numerical Solution for Laminar Two Dimensional Flow About a Cylinder Oscillating in a Uniform Stream
(The American Society of Mechanical Engineers (ASME), 1982)A finite difference model is presented for viscous two dimensional flow of a uniform stream past an oscillating cylinder. A noninertial coordinate transformation is used so that the grid mesh ... -
Discussion: “An Experiment Concerning the Confluence of a Wake and a Boundary Layer” (Bario, F., Charnay, G., and Papailiou, K. D., 1982, ASME J. Fluids Eng., 104, pp. 18–23)
(The American Society of Mechanical Engineers (ASME), 1982) -
An Analysis of Unsteady Torque on a Two-Dimensional Radial Impeller
(The American Society of Mechanical Engineers (ASME), 1982)Unsteady flows around radial impellers are analyzed by the use of singularity methods. Unsteady torque is given for transient and/or sinusoidal flow rate and/or angular velocity fluctuation. It ...