Journal of Fluids Engineering: Recent submissions
Now showing items 7721-7740 of 9024
-
Compressibility Effect in Two-Phase Flow and Its Application to Flow Metering With Orifice Plate and Convergent-Divergent Nozzle
(The American Society of Mechanical Engineers (ASME), 1983)The effect of solution gas on the two-phase flow behavior through an orifice plate and a convergent-divergent nozzle has been investigated with regard to the flow metering of compressible ... -
Collapse of a Cavitating Vortex Ring
(The American Society of Mechanical Engineers (ASME), 1983) -
Discussion: “Measurements of the Spray Angle of Atomizing Jets” (Wu, K.-J., Su, C.-C., Steinberger, R. L., Santavicca, D. A., and Bracco, F. V., 1983, ASME J. Fluids Eng., 105, pp. 406–413)
(The American Society of Mechanical Engineers (ASME), 1983) -
Measurements of the Spray Angle of Atomizing Jets
(The American Society of Mechanical Engineers (ASME), 1983)Liquid jets are considered issuing from single-hole, round nozzles into quiescent gases under conditions such that they break up into a well defined conical spray immediately at the nozzle exit ... -
Discussion: “Low Cycle Fatigue Damage in Pressure-Vessel Materials” (Sessler, J. G., and Weiss, Volker, 1963, ASME J. Basic Eng., 85, pp. 539–545)
(The American Society of Mechanical Engineers (ASME), 1963) -
Measurement of Pointwise Juncture Condition of Temperature at the Interface of Two Bodies in Sliding Contact
(The American Society of Mechanical Engineers (ASME), 1963)An apparatus is described for bringing a rider specimen and a slider specimen into continuous sliding contact so that significant temperatures at the interface are achievable. The design is ... -
Cavitation Inception in Pumps
(The American Society of Mechanical Engineers (ASME), 1982) -
Cavitation in an Extremely Limited Flow Through Very Small Orifices
(The American Society of Mechanical Engineers (ASME), 1982)In order to clarify the role of cavitation nuclei upon inception, the behavior of inception was carefully investigated in an extremely limited water flow through very small orifices less than ... -
Some Experiments With Specific Types of Cavitation on Ship Propellers
(The American Society of Mechanical Engineers (ASME), 1982)The influence of the boundary layer and of the nuclei content of the fluid on cavitation inception is investigated. Two models of ship propellers, displaying sheet cavitation and bubble cavitation ... -
Discussion: “Measurement of the Effects of Viscosity on Aerofoil Lift Using the Electrolytic Tank” (Platt, A., and Norbury, J. F., 1963, ASME J. Basic Eng., 85, pp. 392–399)
(The American Society of Mechanical Engineers (ASME), 1963) -
The Onset of Bubble-Ring Cavitation on Hemispherical Headforms
(The American Society of Mechanical Engineers (ASME), 1982)An approximate theory is developed to predict the onset of cavitation on hemispherical headforms for Reynolds numbers at which laminar separation is known to occur. Insofar as it is possible, ... -
Discussion: “Preston Tube Calibrations and Direct Force Floating Element Measurements in a Two-Dimensional Turbulent Boundary Layer” (McAllister, J. E., Pierce, F. J., and Tennant, M. H., 1982, ASME J. Fluids Eng., 104, pp. 156–160)
(The American Society of Mechanical Engineers (ASME), 1982) -
Drag Reduction in Flow of Coal-Oil Suspensions
(The American Society of Mechanical Engineers (ASME), 1982)Pipe flow characteristics of coal-oil mixtures (C.O.M.) are studied by a pipe flow facility consisting of a Tri-Rotor positive displacement pump, which draws fluid from a reservoir tank and ... -
Wind Induced Forces on Trees
(The American Society of Mechanical Engineers (ASME), 1982) -
Discharge Jet Interaction With Multiple Port Diffusers
(The American Society of Mechanical Engineers (ASME), 1982)A model for the flow dynamics and mixing in the near-field of a multiple port outfall diffuser is postulated. It employs the equations for gross conservation of mass, momentum, and buoyancy ... -
Transverse Oscillations of a Vertical Pile in Waves
(The American Society of Mechanical Engineers (ASME), 1982)A cantilevered pile, flexible only in the transverse direction, has been submitted to wave action. It has been found that resonance transverse vibrations, with natural frequency fn , are induced ... -
Laminar Flow in a Cylindrical Container With a Rotating Cover
(The American Society of Mechanical Engineers (ASME), 1982)Unsteady and steady flow in a cylindrical chamber with a rotating cover has been studied for two Reynolds numbers and three aspect ratio values. The structure of the velocity and pressure ... -
Discussion: “Cumulative Plastic Deformation in Rolling Contact” (Moyar, G. J., and Sinclair, G. M., 1963, ASME J. Basic Eng., 85, pp. 105–112)
(The American Society of Mechanical Engineers (ASME), 1963) -
A Flow Model for the Effect of a Slanted Base on Drag
(The American Society of Mechanical Engineers (ASME), 1982)Experiments by Morel have shown that slanting the base of a bluff body causes large variations in the drag, as the slant angle changes. For a particular, critical slant angle the drag changes ... -
Complete Velocity Profile and “Optimum” Skin Friction Formulas for the Plane Wall-Jet
(The American Society of Mechanical Engineers (ASME), 1982)An analytic expression for the complete velocity profile of a plane, turbulent wall-jet in “stagnant” surroundings is obtained by coupling Spalding’s single formula for the inner layer with a ...