Journal of Fluids Engineering: Recent submissions
Now showing items 6721-6740 of 9024
-
Discussion: “Frictional Characteristics of Liquid Hydrostatic Journal Bearings” (Shinkle, J. N., and Hornung, K. G., 1965, ASME J. Basic Eng., 87, pp. 163–167)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Analysis and Test of the Screw Seal in Laminar and Turbulent Operation” (McGrew, J. M., and McHugh, J. D., 1965, ASME J. Basic Eng., 87, pp. 153–162)
(The American Society of Mechanical Engineers (ASME), 1965) -
Turbulent Boundary-Layer Growth in Annular Diffusers
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Power-Transfer Characteristics for Compressible Flow From a Stationary Nozzle to a Detached Receiver” (Weng, Cheng-Kuo, 1965, ASME J. Basic Eng., 87, pp. 23–27)
(The American Society of Mechanical Engineers (ASME), 1965) -
A Table of the Journal-Bearing Integral
(The American Society of Mechanical Engineers (ASME), 1965)A comprehensive list of recursion formulas is given for integrals of the type sinl θ cosm θ dθ(1 + ε cos θ)n. -
Elastic Orifices for Gas Bearings
(The American Society of Mechanical Engineers (ASME), 1960) -
An Investigation Into the Performance of Two ISA Metering Nozzles of Finite and Zero Area Ratio
(The American Society of Mechanical Engineers (ASME), 1965)The flow through two ISA nozzles of area ratio zero and 0.4 was investigated to determine the nature of the flow and its variation with Reynolds number. Separation occurs within the nozzle ... -
Significance of the Vortex Breakdown Phenomenon
(The American Society of Mechanical Engineers (ASME), 1965)The essential points in the author’s published theory of this phenomenon are summarized, and their implications with regard to longitudinal vortex flows in general are reviewed. The primary aim ... -
A Photographic Study of the Dynamics and Damage Capabilities of Bubbles Collapsing Near Solid Boundaries
(The American Society of Mechanical Engineers (ASME), 1965)The effect of proximal rigid boundaries on the motion and damage capabilities of spark bubbles is investigated by means of a qualitative photographic study. It is determined that an axially ... -
Step Responses of Liquid Lines With Frequency-Dependent Effects of Viscosity
(The American Society of Mechanical Engineers (ASME), 1965)Universal step-response plots are given from theoretical considerations for rigid cylindrical lines containing a compressible Newtonian laminar-flow liquid. The pressure and flow step inputs and ... -
Effect of Surface Roughness on Cavitation Performance of Hydrofoils—Report 1
(The American Society of Mechanical Engineers (ASME), 1965)The effect of surface roughness on hydrofoil characteristics, particularly cavitation performance, was studied experimentally. It was intended to initiate the first of a series of studies to ... -
Laminar Boundary Layers and Their Separation From Curved Surfaces
(The American Society of Mechanical Engineers (ASME), 1965)The equation of motion in a laminar boundary layer on curved surfaces has been developed from the Navier-Stokes equations. After an order-of-magnitude analysis terms of highest and next order ... -
Pressure Surges in Magnetoviscous Flow
(The American Society of Mechanical Engineers (ASME), 1965)An examination is made of the effect produced by an externally applied magnetic field when the flow of an electrically conducting fluid is stopped by the sudden closure of a valve. The fluid ... -
Distortion of Short Pulses in Tapered Tube Pulse Transformers. Part II—Viscous Liquid
(The American Society of Mechanical Engineers (ASME), 1965)A short pulse of pressure or volume flux can be changed in magnitude by sending it through a tapered tube. However, both the geometry of the taper and viscous shear cause the pulse to ... -
Distortion of Short Pulses in Tapered Tube Pulse Transformers. Part I—Inviscid Liquid
(The American Society of Mechanical Engineers (ASME), 1965)A tapered pipe (or “line”) is a convenient transformer for pulses of pressure or volume flux, but the pulse usually becomes distorted, depending on the geometry of the taper. The principal ... -
Initial Phases of Damage to Test Specimens in a Cavitating Venturi
(The American Society of Mechanical Engineers (ASME), 1965)The detailed characteristics of pitting in the early phases of cavitation damage incurred by test specimens inserted into the diffusing portion of a cavitating venturi are shown pictorially and ... -
Supersonic Diffuser for Radial and Mixed Flow Compressors
(The American Society of Mechanical Engineers (ASME), 1960)Presentation is made for the design concepts of a novel diffuser that handles supersonic flow at the exit of radial and mixed flow compressors. The guide vanes incorporating a V shape at the ... -
The Reflection of Waterhammer Pressure Waves From Minor Losses
(The American Society of Mechanical Engineers (ASME), 1965)This paper deals with the reflection produced when a waterhammer pressure wave encounters any device that produces a sudden energy loss such as an orifice, a valve, or an elbow. The classical ... -
Use of Hydrogen Bubbles for Quantitative Determination of Time-Dependent Velocity Fields in Low-Speed Water Flows
(The American Society of Mechanical Engineers (ASME), 1965)Improved flow-visualization methods based on the hydrogen-bubble technique are described. Use of “combined-time-streak markers” allows quantitative measurement of the instantaneous velocity field in ... -
An Analytical and Experimental Study of the Plane, Incompressible, Turbulent Free-Shear Layer With Arbitrary Velocity Ratio and Pressure Gradient
(The American Society of Mechanical Engineers (ASME), 1965)A first-order approximation is derived in similarity coordinates for the velocity variation across a mixing zone between two streams of different velocities in an arbitrary pressure grudient. The ...