Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7221-7240 of 7723
-
Review of Materials Processing Literature 1973–1975, German Language Literature—Part 2: Metal Removal
(The American Society of Mechanical Engineers (ASME), 1977) -
Review of Materials Processing Literature 1973–1975, German Language Literature—Part 1: Metal Forming
(The American Society of Mechanical Engineers (ASME), 1977) -
Dynamics of a Freely Swinging Compound Pendulum
(The American Society of Mechanical Engineers (ASME), 1977) -
ASME Review of Materials Processing Literature 1973–1975: Grinding
(The American Society of Mechanical Engineers (ASME), 1977) -
A Note on Small-Scale Design Optimization
(The American Society of Mechanical Engineers (ASME), 1977) -
Reliability Analysis of Machine Tool Structures
(The American Society of Mechanical Engineers (ASME), 1977)A method of estimating the reliability of machine tool structures is developed. The reliability analysis of horizontal milling machines in various failure modes, like static deflection, fundamental ... -
Discussion: “Tool-Life Distributions—Parts 1 and 2” (Ramalingam, S., and Watson, J. D., 1977, ASME J. Eng. Ind., 99, pp. 519–528)
(The American Society of Mechanical Engineers (ASME), 1977) -
Bunker Design—Part 1: Bunker Outlet Design and Initial Measurements of Wall Pressures
(The American Society of Mechanical Engineers (ASME), 1977)Experiments have shown that the Jenike bunker outlet design method is accurate with respect to both the flow pattern (mass flow or funnel flow) and the minimum outlet required. Initial ... -
Bunker Design—Part 3: Wall Pressures and Flow Patterns in Funnel Flow
(The American Society of Mechanical Engineers (ASME), 1977)A maximum of four zones have been found to exist within a funnel flow bunker. The wall pressures depend upon whether or not material is flowing along the wall. High pressures were found ... -
Bunker Design—Part 2: Wall Pressures in Mass Flow
(The American Society of Mechanical Engineers (ASME), 1977)Measurements of wall pressures have been carried out in a 1.5-m-dia mass flow bunker with three materials. The high flow pressures generated at the top of the cone fluctuate and are unevenly ... -
Bunker Design—Part 4: Recommendations
(The American Society of Mechanical Engineers (ASME), 1977)The results of the preceding experimental investigation have been applied to the design of bunkers. Examples are given which show how the required wall thickness can be determined by horizontal ... -
Effect of Track Geometry and Rail Vehicle Suspension on Passenger Comfort in Curves and Transitions
(The American Society of Mechanical Engineers (ASME), 1977)Passenger comfort is an important constraint on high-speed operation in curves and transitions. The effect of track geometry and vehicle suspension characteristics on passenger comfort were ... -
An Analysis of Wave Convection of Rolling Bodies
(The American Society of Mechanical Engineers (ASME), 1977)A bond graph model of wave convection of rolling bodies is developed. The governing non-linear state space equations are derived directly from the bond graph and solved numerically for various ... -
Matrix Representation and Prediction of Three-Dimensional Cutting Forces
(The American Society of Mechanical Engineers (ASME), 1977)Matrix geometry techniques are applied to predicting three-dimensional cutting forces. In the present model a specific cutting plane is located and two-dimensional metal cutting theory is applied. ... -
Wheel/Rail Vertical Forces in High-Speed Railway Operation
(The American Society of Mechanical Engineers (ASME), 1977)The nature and magnitude of the vertical forces between a railway vehicle wheel and the rail at a dipped rail joint is investigated using methods developed by British Rail. The dependence of ... -
Dynamic Simulation of Freight Car and Lading During Impact
(The American Society of Mechanical Engineers (ASME), 1977)A dynamic analysis is presented to explain damage to railroad cars and ladings resulting from impacts. In the analysis, a mathematical model consisting of the car body and freight in the car ... -
A New Look at Subcritical Quenching (SCT) for Fatigue Strength Improvement
(The American Society of Mechanical Engineers (ASME), 1977)A comprehensive summary of in-house information concerned with thermal prestressing of large forgings for fatigue strength improvement is presented. Seven commercial grades of carbon and alloy ... -
Maximizing the Efficiency of Your Bucket Wheel Reclaimer
(The American Society of Mechanical Engineers (ASME), 1977)Proper application of a track-mounted reclaimer in a storage yard requires knowledge of the machine and the parameters which affect its efficiency. Several stockpile systems are discussed and ... -
Discussion: “On The Doubly Regenerative Stability of a Grinder: The Combined Effect of Wheel and Workpiece Speed” (Thompson, R. A., 1977, ASME J. Eng. Ind., 99, pp. 237–241)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Cable Kinking Analysis and Prevention” (Ross, A. L., 1977, ASME J. Eng. Ind., 99, pp. 112–115)
(The American Society of Mechanical Engineers (ASME), 1977)