Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6961-6980 of 7723
-
Discussion: “Strength of Thick-Walled Pressure Vessels for Materials With Directional Properties” (Dapprich, A. E., Marin, Joseph, and Weng, Tu-Lung, 1962, ASME J. Eng. Ind., 84, pp. 197–202)
(The American Society of Mechanical Engineers (ASME), 1962) -
Radius of Curvature of a Double Helix
(The American Society of Mechanical Engineers (ASME), 1962) -
Feasibility of Pressure Hulls for Ultradeep Running Submarines
(The American Society of Mechanical Engineers (ASME), 1962)Whether the next generation of submarines can operate more deeply depends on the feasibility of developing pressure hull structures sufficiently strong to resist intense external pressure, but ... -
Analytical Determination of Poles in the Coincidence Position of Links in Four-Bar Mechanisms Required for Valves Correctly Apportioning Three Fluids in a Chemical Apparatus
(The American Society of Mechanical Engineers (ASME), 1962)In an important chemical apparatus, admission of three fluids had to be made in quantities required by the correct reaction cycle. For the control of the fluid admission valves, four-bar ... -
Stability of the High-Speed Journal Bearing Under Steady Load: 1—The Incompressible Film
(The American Society of Mechanical Engineers (ASME), 1962)The phenomenon of oil-film whirl in bearings subjected to steady external loads is analyzed. The journal, assumed to be a particle mass, is subjected to the action of two forces; namely, the ... -
An Exploratory Study of Stress Concentrations in Thermal Shock Fields
(The American Society of Mechanical Engineers (ASME), 1962)Exploratory investigations were performed on the effect of stress concentrations upon the stresses generated in a free elastic plane space by thermal shock applied to the boundary. The emphasis ... -
Shrink Fits of Moderately Long Bands on Thin-Walled Cylinders
(The American Society of Mechanical Engineers (ASME), 1962)It is shown that lateral pressure, axial force, and radial interference all may be treated by a uniform procedure, when a moderately narrow ring is shrunk onto a uniformly loaded thin-walled ... -
Load-Deflection Behavior of Conical Spiral Compression Springs
(The American Society of Mechanical Engineers (ASME), 1962)The geometry of both the Archimedean and the logarithmic spiral, when formed into the third dimension, is considered. Changes in profile resulting from the choice of constant helix angle and ... -
Stresses in Tapered Transition Joints in Pipelines and Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1962)Theoretical formulas were developed which provide a means of computing the stresses in and near a tapered transition joint when the shell is subjected to internal pressure. The theoretical ... -
Design of Perforated Plates
(The American Society of Mechanical Engineers (ASME), 1962)This paper describes a method for calculating stresses and deflections in perforated plates with a triangular penetration pattern. The method is based partly on theory and partly on experiment. ... -
Runout Path of an Airplane Equipped With Skids
(The American Society of Mechanical Engineers (ASME), 1962)Equations of motion of the airplane subject to the influence of cross wind, rudder steering, and drag chute, during runout, are developed which would be valid even when the direction-of-travel ... -
Discussion: “Feasibility of Pressure Hulls for Ultradeep Running Submarines” (Wenk, Jr., Edward, 1962, ASME J. Eng. Ind., 84, pp. 373–391)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Stability of the High-Speed Journal Bearing Under Steady Load: 1—The Incompressible Film” (Reddi, M. M., and Trumpler, P. R., 1962, ASME J. Eng. Ind., 84, pp. 351–357)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “An Exploratory Study of Stress Concentrations in Thermal Shock Fields” (Becker, Herbert, 1962, ASME J. Eng. Ind., 84, pp. 343–348)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Shrink Fits of Moderately Long Bands on Thin-Walled Cylinders” (Paul, Burton, 1962, ASME J. Eng. Ind., 84, pp. 338–341)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Load-Deflection Behavior of Conical Spiral Compression Springs” (Wang, Han-Chung, and Worley, Will J., 1962, ASME J. Eng. Ind., 84, pp. 329–337)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Stresses in Tapered Transition Joints in Pipelines and Pressure Vessels” (Rodabaugh, E. C., and Atterbury, T. J., 1962, ASME J. Eng. Ind., 84, pp. 321–328)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Design of Perforated Plates” (O’Donnell, W. J., and Langer, B. F., 1962, ASME J. Eng. Ind., 84, pp. 307–319)
(The American Society of Mechanical Engineers (ASME), 1962) -
The Effect of Vibration on Plastic Flow in Coining
(The American Society of Mechanical Engineers (ASME), 1962)Coining with a superimposed vibrational load of 800 lb and with a relatively low frequency of 130 cps was investigated. The materials were commercially pure lead and aluminum which were chosen ... -
The Mechanics of the Coining Process
(The American Society of Mechanical Engineers (ASME), 1962)The mechanism of coining is analyzed and several approximate solutions are given. The solutions were based on the strip, slip-line, and upper-bound methods of analysis. Comparison of the solutions ...