Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6681-6700 of 7723
-
Measurement of Cotton Fiber Tenacity on 1/8 Gage HVI Tapered Bundles
(The American Society of Mechanical Engineers (ASME), 1982)The inherent precision and accuracy of the methods used for measuring the fiber bundles strength of cotton encompass the variability among individual measurements and the confidence with which ... -
Discussion: “Rate of Strain Effect in Metal Cutting” (Oxley, P. L. B., 1963, ASME J. Eng. Ind., 85, pp. 335–337)
(The American Society of Mechanical Engineers (ASME), 1963) -
Low Velocity Impact of a Viscoelastic Beam
(The American Society of Mechanical Engineers (ASME), 1982)A theoretical solution for the response of a viscoelastic beam to off-center low speed transverse impact is presented. The flexural model adopted for investigation consists of a uniform ... -
Discussion: “Rigid-Plastic Finite-Element Analysis of Plane Strain Rolling” (Li, Guo-Ji, and Kobayashi, S., 1982, ASME J. Eng. Ind., 104, pp. 55–63)
(The American Society of Mechanical Engineers (ASME), 1982) -
Effect of Weather, Age, and Cyclic Pressurizations on Structural Performance of Acrylic Plastic Spherical Shells Under External Pressure Loading
(The American Society of Mechanical Engineers (ASME), 1982)Weathering, aging, and cyclic application of stresses to acrylic plastic degrades its physical properties. The rate of degradation must be known if the useful life of load-carrying acrylic ... -
Pressure Resistant Bulkhead Penetrators for Fiber Optics in Deep Ocean Applications
(The American Society of Mechanical Engineers (ASME), 1982)This paper describes results obtained at the Naval Ocean Systems Center, San Diego, under Independent Exploratory Development funding. The objective was to develop a robust, fully-demountable, ... -
Development of a Cross-Braced Truck
(The American Society of Mechanical Engineers (ASME), 1982)This paper describes the analytical, design, and test processes utilized in development of a cross-braced freight car truck intended for service on American railroads. Analytical techniques predict ... -
Discussion: “Development of a Cross-Braced Truck” (Mulcahy, H. W., and Weeks, R. J., 1982, ASME J. Eng. Ind., 104, pp. 182–188)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Effect of Weather, Age, and Cyclic Pressurizations on Structural Performance of Acrylic Plastic Spherical Shells Under External Pressure Loading” (Stachiw, J. D., and Dolan, R. B., 1982, ASME J. Eng. Ind., 104, pp. 190–200)
(The American Society of Mechanical Engineers (ASME), 1982) -
Acoustic Similarity Laws for Fans
(The American Society of Mechanical Engineers (ASME), 1982)In order to verify experimentally acoustic similarity laws for fans, experiments were made with three, dimensionally similar centrifugal fans of 140, 280, and 560 mm impeller diameter. The fans ... -
On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel
(The American Society of Mechanical Engineers (ASME), 1982)An AISI 4340 Steel (325 BHN) was machined at various speeds up to 2500 m/min (8000 SFPM). Longitudinal midsections of the chips were examined metallurgically to delineate the differences in ... -
Review of Noise Reduction Methods for Centrifugal Fans
(The American Society of Mechanical Engineers (ASME), 1982)Several methods of reducing the noise of centrifugal fans are discussed, most of which were aimed at a lower blade passage frequency level because tonal noise components are of particular ... -
Transfer Lines: A Deterministic Model for Buffer Capacity Selection
(The American Society of Mechanical Engineers (ASME), 1982)A key problem in transfer line design is that of determining what size should be assigned to intermediate storage buffers in order to maintain a desired production rate despite the imbalances ... -
Experiments on Adaptive Constrained Control of a CNC Lathe
(The American Society of Mechanical Engineers (ASME), 1982)The technological and economic aspects of the on-line optimization of turning operations on lathes equipped with a Computerized Numerical Control (CNC) are discussed. A model of the machining ... -
A Study of Metal Flow Ahead of Tool Face With Large Negative Rake Angle
(The American Society of Mechanical Engineers (ASME), 1982)Although the chip formation mechanism by a tool having a large negative rake angle is not well known, it is very important to make the process clear in order to get high quality in finished ... -
The Prediction of Surface Accuracy in End Milling
(The American Society of Mechanical Engineers (ASME), 1982)In the end milling process, the cutting forces during machining produce deflection of the cutter and workpiece which result in dimensional inaccuracies or surface error on the finished component. ... -
Characteristics, Riemann Invariants, and Plane Strain Plasticity
(The American Society of Mechanical Engineers (ASME), 1982)The set of equations governing plane strain plasticity are treated here as a system of homogeneous quasi-linear partial differential equations. Characteristics and Riemann invariants are defined ... -
Predicting the Shear Plane Angle in Machining From Workmaterial Strain-Hardening Characteristics
(The American Society of Mechanical Engineers (ASME), 1982)An upper-bound type analysis is presented for predicting the “shear plane angle,” φ, in machining, using workmaterial strain-hardening characteristics. The degree of strain-hardening is quantified ... -
Criterion for the Prevention of Core Fracture During Extrusion of Bimetal Rods
(The American Society of Mechanical Engineers (ASME), 1982)Based on the upper-bound theorem in limit analysis, a theoretical model for core fracture in bimetal rods during extrusion has been developed and a fracture criterion established. The variables ... -
Effects of Die Shoulder on the Prolateness and Deformation in the Bulge Test
(The American Society of Mechanical Engineers (ASME), 1982)In the present investigation, the prolateness and the deformation of sheet metal deformed under lateral pressure with dies of different shoulder radii are analyzed. It is found that at the ...