Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6661-6680 of 7723
-
Development of a 36-Axle Schnabel Rail Car
(The American Society of Mechanical Engineers (ASME), 1982)The high capacity 36-Axle Schnabel Rail Car recently delivered to Combustion Engineering, Inc. (C-E), is traced from initial inception through delivery. The Schnabel Car carries its load suspended ... -
Discussion: “Theoretical Aspects of High-Speed Shear in Face Centered Cubic Metals” (von Turkovich, B. F., and Trigger, K. J., 1963, ASME J. Eng. Ind., 85, pp. 357–363)
(The American Society of Mechanical Engineers (ASME), 1963) -
Twist Moments and Deformations in Submarine Cable Installation
(The American Society of Mechanical Engineers (ASME), 1982)Submarine cable systems made up of combinations of armorless cable and armored cable are subject to twist moments and deformations during installation. These stresses and strains may damage the ... -
Influence of Exit Impedance on Finite Difference Solutions of Transient Acoustic Mode Propagation in Ducts
(The American Society of Mechanical Engineers (ASME), 1982) -
Tensile Fracture of Drawn Copper and Mild Steel
(The American Society of Mechanical Engineers (ASME), 1982)Annealed OFHC copper and SAE 1018 steel were reduced by multipass drawing from diameters of 25.4 mm (and smaller) to 11.8 mm. A comparison was made of the experimental draw stresses and those ... -
Drill Point Geometry and Optimization
(The American Society of Mechanical Engineers (ASME), 1982)The geometrical parameters of the drill point, i.e., relief angles, chisel form, web size, and errors of symmetry have a major influence on drill performance. This paper deals with geometrical ... -
Rigid-Plastic Finite-Element Analysis of Plane Strain Rolling
(The American Society of Mechanical Engineers (ASME), 1982)The plane-strain rolling problem was solved by the rigid-plastic finite-element method based on the infinitesimal theory of plastic deformation. Both nonsteady-state solutions and steady-state ... -
Mathematical Modeling of Metal Extrusion Process
(The American Society of Mechanical Engineers (ASME), 1982)The present paper describes a novel calculation procedure for the detailed prediction of flow field during the process of metal extrusion. The flow of metal has been regarded as a flow of ... -
Shape Changes in the Upsetting of Slender Cylinders
(The American Society of Mechanical Engineers (ASME), 1982)Mild steel and aluminum alloy cylinders were incrementally upset with good lubrication and with sticking friction, and the development of shape was followed by measuring the diameters of the ... -
Vibration of Wide Band Saw Blades
(The American Society of Mechanical Engineers (ASME), 1982)The vibration and stability of wide band saw blades is investigated using an axially moving plate model which includes the effect of in-plane stresses upon stiffness. The equation of motion ... -
Application of the Regeneration Spectrum Method to Wheel Regenerative Chatter in Grinding
(The American Society of Mechanical Engineers (ASME), 1982)A convenient stability analysis technique for the approximate computation of wheel regenerative chatter growth rates in cylindrical grinding processes is presented. For such processes, the locations ... -
Plastic Flow Instability Under Compressive Loading During Shear Spinning Process
(The American Society of Mechanical Engineers (ASME), 1982)The sudden appearance of a material bulge beneath the roller during tube spinning operation (referred to as “plastic instability”) is considered experimentally and examined quantitatively via an ... -
Compensatory Control of Roundness Error in Cylindrical Chuck Grinding
(The American Society of Mechanical Engineers (ASME), 1982)Traditional methods of improving the roundness generating capability of cylindrical grinding machine calls for the manufacture of an ultra-high precision spindle and bearings and careful and ... -
Analysis of Extrusion or Drawing of Polygonal Sections Through Straightly Converging Dies
(The American Society of Mechanical Engineers (ASME), 1982)This paper describes a new method for obtaining optimal die shape which produces minimal stress in the extrusion or the drawing of nonaxisymmetric sections from round bar stock. The surface ... -
Discussion: “Use of Chip Tension to Obtain a Stress-Strain Curve From Metal Cutting Tests” (Finnie, I., and Wolak, J., 1963, ASME J. Eng. Ind., 85, pp. 351–355)
(The American Society of Mechanical Engineers (ASME), 1963) -
Drawing Force in Deep Drawing of Cylindrical Cup With Flat-Nosed Punch
(The American Society of Mechanical Engineers (ASME), 1982)A method for estimating the maximum drawing force in the deep drawing of cylindrical cups with flat-nosed punch is developed. The criterion is obtained using the load maximum principle for ... -
Erratum: “On the Acoustical Implications of Vortex Shedding from an Exhaust Pipe” (Journal of Engineering for Industry, 1981, 103, pp. 378–384)
(The American Society of Mechanical Engineers (ASME), 1982) -
A Nondimensional Approach to the Membrane Stresses in Axisymmetrical Thin Shells
(The American Society of Mechanical Engineers (ASME), 1982) -
Acceleration Detection and Inertia Compensation of Pantograph Head Using a Constant Flow Hydraulic Servo
(The American Society of Mechanical Engineers (ASME), 1982)The paper presents a novel form of acceleration detection which is suitable for use in hydraulic amplification stages for relatively low frequency, high power output servo systems. The acceleration ... -
Effect of Crystallinity and Orientation on Oscillation During Drawing of Polyethylene Terephthalate
(The American Society of Mechanical Engineers (ASME), 1982)Stress oscillations have been observed in cold-drawn synthetic monofilaments and films. The effects of these oscillations on cross-section and lengthwise filament properties have been under ...