Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6601-6620 of 7723
-
Discussion: “Analysis of Wire Drawing and Extrusion Through Conical Dies of Small Cone Angle” (Avitzur, Betzalel, 1963, ASME J. Eng. Ind., 85, pp. 89–95)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Frictional Boundary Conditions in Plastic Compression” (Pearsall, G. W., and Backofen, W. A., 1963, ASME J. Eng. Ind., 85, pp. 68–75)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “The Influence of Extreme Speeds and Rake Angles in Metal Cutting” (Findley, W. N., and Reed, R. M., 1963, ASME J. Eng. Ind., 85, pp. 49–64)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Study on Wear of Grinding Wheels: 1—Bond Fracture in Grinding Wheels” (Yoshikawa, Hiroyuki, and Sata, Toshio, 1963, ASME J. Eng. Ind., 85, pp. 39–42)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Basic Investigation of Tool Wear” (Takeyama, H., and Murata, R., 1963, ASME J. Eng. Ind., 85, pp. 33–37)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “On Determining the Hardness of Grinding Wheels—II” (Colwell, L. V., 1963, ASME J. Eng. Ind., 85, pp. 27–32)
(The American Society of Mechanical Engineers (ASME), 1963) -
Temperature Gradients in Skirt Supports of Hot Vessels
(The American Society of Mechanical Engineers (ASME), 1963)A discussion of the variables involved in the temperature gradient along a skirt support for a hot vessel is presented. A method is presented for reasonably approximating the maximum gradient ... -
Circumferential Stresses in Pressure Vessel Shells of Revolution
(The American Society of Mechanical Engineers (ASME), 1963) -
Thin-Shell Pressure Vessel Theoretical and Experimental Stresses
(The American Society of Mechanical Engineers (ASME), 1963)This paper is concerned primarily with a comparison of experimental and theoretical shell-to-head junction stresses of a thin-shell pressure vessel. The portion of the vessel with which this ... -
Drill String Vibrations Due to Intermittent Contact of Bit Teeth
(The American Society of Mechanical Engineers (ASME), 1963)An analysis of the longitudinal forces and the resulting longitudinal motions of an idealized drill string is presented. The only external force excitation considered occurs at the bit and is ... -
Fire and Quench Tests of Refinery Valves
(The American Society of Mechanical Engineers (ASME), 1963)Valve bodies made of seven materials from five suppliers were thermal-shock tested by heating to 1300 F, 1500 F, 1600 F, or 1800 F and then quenching with a fire-hose stream. None cracked ... -
Process Kinetics as Design Criteria for Bio-Oxidation of Petrochemical Wastes
(The American Society of Mechanical Engineers (ASME), 1963)Biological oxidation is widely used in industrial waste treatment. In order to achieve economic design, a thorough understanding of the process and its kinetics is necessary. This paper defines ... -
Effect of Tool Joints on Passages of Plane Longitudinal and Torsional Waves Along a Drill Pipe
(The American Society of Mechanical Engineers (ASME), 1963)The effect of tool joints on the passage of plane longitudinal and torsional waves along a drill pipe was studied. An approximate solution to the governing equations of motion was found, and ... -
Deteriorative Effects of Both Usage and Long Term Storage on Aircraft and Missile Hydraulic Fluids
(The American Society of Mechanical Engineers (ASME), 1963) -
Aerospace Pneumatic Control Systems
(The American Society of Mechanical Engineers (ASME), 1963)This paper attempts to deduce the growth pattern of aerospace pneumatic control systems, where pneumatic systems are defined as those employing any gas as a working medium. Various important ... -
Bearings for Vacuum Operation—Retainer Material and Design
(The American Society of Mechanical Engineers (ASME), 1963)This report describes the initial phase of an investigation of the high-speed operation of miniature ball bearings, with metallic film lubrication, in a vacuum environment. Phase I of this study ... -
Discussion: “Temperature Gradients in Skirt Supports of Hot Vessels” (Bergman, D. J., 1963, ASME J. Eng. Ind., 85, pp. 219–223)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Circumferential Stresses in Pressure Vessel Shells of Revolution” (Zick, L. P., and St. Germain A. R., 1963, ASME J. Eng. Ind., 85, pp. 201–216)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Fire and Quench Tests of Refinery Valves” (Heckler, N. B., Petkus, J. J., Randall, P. N., and Tisinai, G. F., 1963, ASME J. Eng. Ind., 85, pp. 173–182)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Process Kinetics as Design Criteria for Bio-Oxidation of Petrochemical Wastes” (Busch, A. W., 1963, ASME J. Eng. Ind., 85, pp. 163–168)
(The American Society of Mechanical Engineers (ASME), 1963)