Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6621-6640 of 7723
-
Discussion: “Aerospace Pneumatic Control Systems” (Sung, C. B., and Taplin, L. B., 1963, ASME J. Eng. Ind., 85, pp. 135–149)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Bearings for Vacuum Operation—Retainer Material and Design” (Evans, Harold E., and Flatley, Thomas W., 1963, ASME J. Eng. Ind., 85, pp. 129–134)
(The American Society of Mechanical Engineers (ASME), 1963) -
General Procedure for Analyzing Thick Shells of Irregular Shapes for Mechanical and Thermal Loading
(The American Society of Mechanical Engineers (ASME), 1963)A general method is presented for analyzing thick shells of irregular shape for mechanical and thermal loading, allowing axial as well as radial thermal gradients. The method takes into account ... -
On the Lateral Creep of Flat Belts
(The American Society of Mechanical Engineers (ASME), 1963)Classical theory is based on one-dimensional (tangential) creep of a flat belt over the pulley. The present paper shows that in virtually every flat belt lateral creep affects performance very ... -
Vector Analysis of Linkages
(The American Society of Mechanical Engineers (ASME), 1963)Expression of vectors in spherical coordinates within an appropriately defined reference frame facilitates explicit, general solutions to a wide range of linkage problems. To demonstrate this, a ... -
Synthesis of Path-Generating Mechanisms by Numerical Methods
(The American Society of Mechanical Engineers (ASME), 1963)Algebraic methods in kinematic synthesis are extended to cases in which the development of iterative numerical procedures are required. Algorithms are developed for the numerical solution of ... -
High Temperature Metal Bellows Seals for Aircraft and Missile Accessories
(The American Society of Mechanical Engineers (ASME), 1963) -
Stability of the High-Speed Journal Bearing Under Steady Load: 2—The Compressible Film
(The American Society of Mechanical Engineers (ASME), 1963)The governing equations for the dynamical system of a self-acting gas-lubricated journal bearing are formulated. An approximate solution for the equilibrium position of the journal center is ... -
Stresses and Deflections in Built-In Beams
(The American Society of Mechanical Engineers (ASME), 1963)Local distortions in the support(s) allow beams to rotate at their built-in end(s). The effect of these rotations is included in the classical equations for the deflections and stresses in ... -
The Optimization of Damping of Four Configurations of a Vibrating Uniform Beam
(The American Society of Mechanical Engineers (ASME), 1963)Approximate analytical expressions for optimum damping for four configurations of forcing and damping a uniform beam were evaluated and the displacement responses for optimum damping values obtained ... -
Response of a Free-Standing or Anchored Explosive-Forming Assembly
(The American Society of Mechanical Engineers (ASME), 1963)This investigation considers an explosive-forming assembly where an elastic base is able to take compressive loads but cannot support tension. The release of the compression without restraint may ... -
Synthesis of Mechanical Vibration Filters With Nonlinear Characteristics
(The American Society of Mechanical Engineers (ASME), 1963)The synthesis of the desired nonlinear characteristics for the spring and damper used to isolate a single mass from a vibrating base is here investigated. The analysis is confined to the ... -
Wave Effects in Viscoelastic Leaf and Compression Spring Mounts
(The American Society of Mechanical Engineers (ASME), 1963)Transmissibility expressions that take wave effects into account are derived for masses mounted on highly viscoelastic leaf springs and compression springs. Approximations suitable for large ratios ... -
Dynamic Characteristics and Design Criteria for a Class of Vibration-Producing Machines
(The American Society of Mechanical Engineers (ASME), 1963)Many self-contained machines used in industry serve to generate a sustained mechanical vibration for performing such diverse operations as vibration testing, hammering, material conveying, impacting, ... -
An Evaluation of the Fixed Point Method of Vibration Analysis for a Particular System With Initial Damping
(The American Society of Mechanical Engineers (ASME), 1963)The maximum steady-state response of a particular linear damped two-degree-of-freedom vibratory system is minimized by determining the optimum damping constant for a single damper. This is ... -
Report of Committee RR-6 Survey: Progress in Railway Mechanical Engineering, 1961–1962
(The American Society of Mechanical Engineers (ASME), 1963)This paper contains the annual report of the ASME Survey Committee RR-6. Developments in Railway Mechanical Engineering from September 1, 1961, to September 1, 1962, pertaining to cars and ... -
Discussion: “General Procedure for Analyzing Thick Shells of Irregular Shapes for Mechanical and Thermal Loading” (Bijlaard, P. P., and Dohrmann, R. J., 1963, ASME J. Eng. Ind., 85, pp. 314–319)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “On the Lateral Creep of Flat Belts” (Fazekas, G. A. G., 1963, ASME J. Eng. Ind., 85, pp. 307–310)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Vector Analysis of Linkages” (Chace, Milton A., 1963, ASME J. Eng. Ind., 85, pp. 289–297)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “High Temperature Metal Bellows Seals for Aircraft and Missile Accessories” (Matt, Richard J., 1963, ASME J. Eng. Ind., 85, pp. 281–287)
(The American Society of Mechanical Engineers (ASME), 1963)