Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6581-6600 of 7723
-
Discussion: “Stresses and Deflections in Built-In Beams” (O’Donnell, W. J., 1963, ASME J. Eng. Ind., 85, pp. 265–272)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Combination of Solutions of the Torsion Problem by Means of a Connection Function” (Carter, William J., 1963, ASME J. Eng. Ind., 85, pp. 12–14)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “Synthesis of Six-Link Plane Mechanisms by Numerical Analysis” (McLarnan, C. W., 1963, ASME J. Eng. Ind., 85, pp. 5–10)
(The American Society of Mechanical Engineers (ASME), 1963) -
1961 Review of Metal Processing Literature
(The American Society of Mechanical Engineers (ASME), 1963)By the members of the Literature Review Committee of the Metal Processing Research Activity of ASME: W. Pentland, Cornell University, Chairman; E. G. Thomsen, University of California, Metal ... -
Development of an Extended Duration 1200 Deg F Torque Motor
(The American Society of Mechanical Engineers (ASME), 1963)The application of high performance fluid power servos for attitude and engine control functions to advanced flight vehicles necessitates advancing the state-of-the-art of hydraulic systems in ... -
Cassinian Domes for Pressure Vessel Design
(The American Society of Mechanical Engineers (ASME), 1963)The necessity for being able to choose the depth and free deflection of a pressure vessel dome independently is shown. A two-parameter equation is presented which allows the designer to choose ... -
Equilibrium Shapes for Pressurized Fiberglas Domes
(The American Society of Mechanical Engineers (ASME), 1963)The netting concept is used to analyse filament wound shells of revolution. First the fiber tensions are resolved parallel and perpendicular to the meridian. These components of the fiber ... -
Maintenance and Support of Hydraulic Thrust Vector Control Systems for Long-Term Unattended Storage
(The American Society of Mechanical Engineers (ASME), 1963)Second-generation ballistic missiles are being developed for compatibility with the concept of long-term storage in permanent underground housing, with missiles in firing position, and in a condition ... -
Analysis of Wire Drawing and Extrusion Through Conical Dies of Small Cone Angle
(The American Society of Mechanical Engineers (ASME), 1963)Analytical expressions are derived for the required front pull for wire drawing, as well as the back push for extrusion. The effect of each of the process variables on these forces is presented ... -
Power Analysis of Cold Strip Rolling
(The American Society of Mechanical Engineers (ASME), 1963)In a previous paper criteria for maximum possible reduction were developed. A simple procedure for the experimental determination of the coefficient of friction was introduced. In this paper a ... -
Frictional Boundary Conditions in Plastic Compression
(The American Society of Mechanical Engineers (ASME), 1963)Distributions of normal stress, shear stress, and coefficient of friction were determined at the interface between a steel tool and a plastically deforming aluminum disk, using two pressure-sensitive ... -
The Influence of Extreme Speeds and Rake Angles in Metal Cutting
(The American Society of Mechanical Engineers (ASME), 1963)A study is presented of the effect of wide variations in speed of cutting and rake angle on orthogonal cutting of several metals—mainly a lead-antimony alloy. It was observed that enormous ... -
Instability in Conventional Spinning of Cones
(The American Society of Mechanical Engineers (ASME), 1963)The condition of flange wrinkling in conventional spinning of cones is established by modifying the theory of instability in deep-drawing of cups. Experiments conducted in order to test the ... -
Study on Wear of Grinding Wheels: 1—Bond Fracture in Grinding Wheels
(The American Society of Mechanical Engineers (ASME), 1963)Fracturing of bond bridges in grinding wheels is explained from the standpoint of brittle-fracture. It is shown that the wear rate of grinding wheels can be expressed as the single exponential ... -
Basic Investigation of Tool Wear
(The American Society of Mechanical Engineers (ASME), 1963)This paper treats a fundamental investigation of tool wear and tool life mainly from the viewpoint of flank wear. The result reveals that the mechanism of tool wear in turning can be classified ... -
On Determining the Hardness of Grinding Wheels—II
(The American Society of Mechanical Engineers (ASME), 1963)This second progress report on the crush grading of grinding wheels by means of force measurements takes up the question of the effect of variations in system rigidity on hardness ratings. ... -
Analysis of Two-Dimensional Motion Resisted by Coulomb Friction
(The American Society of Mechanical Engineers (ASME), 1963)The effect of Coulomb (dry) friction between surfaces of adjacent machine members, either in preventing relative sliding motion or in absorbing energy when relative motion does occur, has ... -
Combination of Solutions of the Torsion Problem by Means of a Connection Function
(The American Society of Mechanical Engineers (ASME), 1963)A method is presented whereby known solutions to the torsion problem may be combined to form new solutions provided that the bar cross section can be broken down into sections for which the ... -
Synthesis of Six-Link Plane Mechanisms by Numerical Analysis
(The American Society of Mechanical Engineers (ASME), 1963)Equations relating the link dimensions and the input and output crank angles are developed for three mechanisms—a Watt linkage and two inversions of the Stephenson linkage. An iterative solution ... -
Some Simplified Solutions for Relatively Stiff Beams on Elastic Foundations
(The American Society of Mechanical Engineers (ASME), 1963)Maximum bending moments, rotations, and deflections of beams resting on elastic foundations and subject to central forces and bending moments are computed on the basis of a linear approximation ...