Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5881-5900 of 7723
-
Prestressing a Two-Layer Pressure Vessel by Plastic Deformation
(The American Society of Mechanical Engineers (ASME), 1965)A method of prestressing two-layer pressure vessels by controlled yielding of the inner layer by internal pressure is described. The required prestressing pressure depends upon the dimensions of ... -
Drawing of Tubes Filled With Particulate Solids
(The American Society of Mechanical Engineers (ASME), 1965)The principal parameters involved in drawing of metal tubes containing metallic, mineral, and organic powders were investigated on small copper, mild steel, and 304 stainless tubing. The type ... -
Tube Sinking and Expanding
(The American Society of Mechanical Engineers (ASME), 1965)In the operations of tube forming, the purpose is to change the diameter of the tube. To achieve this, the tube is drawn through a conical die (tube sinking) to decrease its diameter, or ... -
Analysis of Metal Extrusion
(The American Society of Mechanical Engineers (ASME), 1965)The process of extrusion through a chamber is analyzed. Kinematically admissible velocity fields are utilized to obtain a lower upper-bound solution for the extrusion stress. Assumptions are as ... -
Deformation During Chip Formation
(The American Society of Mechanical Engineers (ASME), 1965)Expressions are derived for the deformed orientation of an initially rectangular grid and the direction of maximum elongation with respect to the rake face of the tool in orthogonal machining. -
Study of the Radiometric Method and Use of the Liquid Scintillation Technique for Tool-Wear Determination
(The American Society of Mechanical Engineers (ASME), 1965)A radiometric method of tool-wear evaluation was investigated and evaluated by comparing the results with those obtained from visual wear measurements. A liquid scintillation technique is presented ... -
Improving Ultrasonic Machining Rates—Some Feasibility Studies
(The American Society of Mechanical Engineers (ASME), 1965)Investigations are reported on the influence on removal rate of slurry liquid cavitation, low temperature, liquid metal, and stress corrosion embrittlement of the work material, tool vibration ... -
Some Effects of Cutting Fluids on Chip Formation in Metal Cutting
(The American Society of Mechanical Engineers (ASME), 1965)In cutting dry AISI C-1025 steel tubing, with a variety of cutting fluids, and with an internally cooled tool, two distinct equilibria were discerned. Chip temper colors indicate that these ... -
Further Investigation of a Relation for Cumulative Fatigue Damage in Bending
(The American Society of Mechanical Engineers (ASME), 1965)The fatigue behavior of several steels, AISI 4130, E52100, and 304 ELC stainless, as well as that of a nonferrous alloy, 5456-H311, was investigated in rotating bending fatigue after these ... -
High-Temperature, Cobalt-Tungsten Alloys for Aerospace Applications
(The American Society of Mechanical Engineers (ASME), 1965)The high-temperature capability and workability of cobalt-tungsten alloys for aerospace applications is discussed. The average life at 1850 F and 15,000 psi of the strongest previously reported ... -
Experiments on Room-Temperature Nernst-Ettingshausen Refrigerators
(The American Society of Mechanical Engineers (ASME), 1965)Cooling experiments with a (transverse) Nernst-Ettingshausen NE refrigerator using properly oriented and shaped single crystals of pure bismuth are described. By cooling the hot junction Th of ... -
Fluid Mechanics of Zero-G Propellant Transfer in Spacecraft Propulsion Systems
(The American Society of Mechanical Engineers (ASME), 1965)The basic requirement of a transfer system for storable propellants is to provide propellant in sufficient quantity to assure proper engine operation. The main propulsion systems of advanced ... -
Discussion: “Drawing of Tubes Filled With Particulate Solids” (Polakowski, N. H., and Mayfield, R. M., 1965, ASME J. Eng. Ind., 87, pp. 80–84)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Analysis of Metal Extrusion” (Avitzur, B., 1965, ASME J. Eng. Ind., 87, pp. 57–69)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Improving Ultrasonic Machining Rates—Some Feasibility Studies” (Pentland, W., and Ektermanis, J. A., 1965, ASME J. Eng. Ind., 87, pp. 39–46)
(The American Society of Mechanical Engineers (ASME), 1965) -
Free Vibration of Initially Stressed Circular Disks
(The American Society of Mechanical Engineers (ASME), 1965)The approximate free vibration characteristics of centrally clamped, variable thickness disks are analyzed by the Rayleigh-Ritz technique. Natural frequencies of transverse vibration are computed, ... -
Analysis of Errors in the Double Hooke Joint
(The American Society of Mechanical Engineers (ASME), 1965)A double Hooke joint consists of two properly connected single Hooke joints for the purpose of transmitting rotation with a uniform angular velocity ratio. Previous kinematic analyses [1, 2, ... -
On Polygonal Action in Roller Chain Drives
(The American Society of Mechanical Engineers (ASME), 1965)Numerical analyses of the kinematics of an idealized model, together with experimental measurements of periodic fluctuations in the angular displacement ratio, are used to supplement existing ... -
The Accuracy of One Method for Mechanism Simulation by Electronic Analog Computer
(The American Society of Mechanical Engineers (ASME), 1965)A method for the simulation of mechanisms on the electronic analog computer has been developed. In this paper a detailed discussion of the accuracy of the simulation is presented. Particular ... -
Solutions to the Vector Tetrahedron Equation
(The American Society of Mechanical Engineers (ASME), 1965)A set of nine closed-form solutions are presented to the single, three-dimensional vector tetrahedron equation, sum of vectors equals zero. The set represents all possible combinations of unknown ...