Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5861-5880 of 7723
-
Three-Dimensional Finite Element Analysis on Open-Die Block Forging Design
(The American Society of Mechanical Engineers (ASME), 1992)Three-dimensional rigid-plastic finite element method was used to analyze the practice of open-die block forging, focusing on the effects of die configurations and forging pass designs. Four ... -
An Ultrasonic Double-Sheet Detection System for Collators
(The American Society of Mechanical Engineers (ASME), 1992)A new ultrasonic method of detecting double sheets in collators has been developed that overcomes several shortcomings of conventional detection techniques. An air curtain efficiently reduces the ... -
The Optimization of Machining Operations Based on a Combined Criterion, Part 1: The Use of Combined Objectives in Single-Pass Operations
(The American Society of Mechanical Engineers (ASME), 1992)The problem of determining the optimum machining conditions for single-pass and multipass operations has been investigated. An objective function incorporating a combination of the minimum production ... -
Application of Finite Element Method to the Design of Superplastic Forming Processes
(The American Society of Mechanical Engineers (ASME), 1992)Finite element method is used as a design tool in the prediction of process parameters for superplastic metal forming processes. The method is used in the design of various plane strain and ... -
Three Dimensional Printing: Rapid Tooling and Prototypes Directly from a CAD Model
(The American Society of Mechanical Engineers (ASME), 1992)Three Dimensional Printing is a process for the manufacture of tooling and functional prototype parts directly from computer models. Three Dimensional Printing functions by the deposition of ... -
The Optimization of Machining Operations Based on a Combined Criterion, Part 2: Multipass Operations
(The American Society of Mechanical Engineers (ASME), 1992)Part 1 of this paper [1] introduced a novel, rational objective function that incorporates both the production cost and total time criteria. In Part 2, the problem of determining the optimum ... -
Finite Element Simulation of Welding of Large Structures
(The American Society of Mechanical Engineers (ASME), 1992)Current simulations of welding distortion and residual stress have considered only the local weld zone. A large elastic structure surrounding a weld, however, can couple with the welding operation ... -
Transient Analysis of an Asymmetric Rotor-Bearing System During Acceleration
(The American Society of Mechanical Engineers (ASME), 1992)This paper deals with the transient vibration of asymmetric rotor systems during acceleration passing through several critical speeds at which synchronous or super-harmonic resonance occurs. The ... -
Tool Status Recording and Its Use in Probabilistic Optimization
(The American Society of Mechanical Engineers (ASME), 1992)In batch production, recording the status of cutting tools and making decisions based on current tool status are important issues. In flexible manufacturing systems, there are normally many tools ... -
Chemical Smoothing of Rough Metal Surfaces
(The American Society of Mechanical Engineers (ASME), 1992)A chemical etching method is investigated as a possible approach to smoothing metal surfaces automatically. In a chemical etching process metal is removed due to chemical reaction and the ... -
The Effect of Particle Feed Rate on the Plastic Media Blast Jet
(The American Society of Mechanical Engineers (ASME), 1992)Paint removal from military aircraft is often done by plastic media blasting (PMB): the use of plastic grit in a conventional blast jet. However, there is some concern that PMB will cause ... -
An Improved Model for Force Transients in Turning
(The American Society of Mechanical Engineers (ASME), 1992)An improved model for force transients in turning is introduced to incorporate the geometry of the cut, as well as plowing at the cutting edge and rubbing of the flank wear land against the ... -
Prediction of Cutting Forces and Tool Breakage in Milling from Feed Drive Current Measurements
(The American Society of Mechanical Engineers (ASME), 1992) -
Predictive Control of a Robotic Grinding System
(The American Society of Mechanical Engineers (ASME), 1992)This paper describes a modified predictive controller that has been interfaced with the robotic weld bead grinding system currently under development at The Charles Stark Draper Laboratory. The ... -
Phase Characteristics of Self-Excited Chatter in Cutting
(The American Society of Mechanical Engineers (ASME), 1992)The behavior of the self-excited chatter in cutting was investigated from the space phase point of view; the space phase is defined as that between outer and inner modulation. Records of ... -
Analysis of Fluid Flow through the Grinding Zone
(The American Society of Mechanical Engineers (ASME), 1992)A theoretical model of fluid flow in grinding has been developed by an analysis of fluid flow through a porous medium. Fluid tangential velocity, radial velocity, depth of penetration into the ... -
The Morphology of Machining Chips Formed During Low Speed Quasi-Orthogonal Machining of CA 360 Brass and a Model for Their Formation
(The American Society of Mechanical Engineers (ASME), 1992)In a previous study of orthogonal machining of CA 360 brass, periodic load fluctuations were related to geometric features observed on the machining chip. In this study, the metallography of ... -
Mechanical and Thermal Stresses in Clamped, Brazed, and Bonded Carbide Tools
(The American Society of Mechanical Engineers (ASME), 1992)A model based on the finite element method is presented for determining of thermal and mechanical stresses in a carbide insert due to heat and cutting forces induced during metal cutting with ... -
Discussion: “A Four-Bar Linkage Adjustable for Variable Straight Line Motions” (Tao, D. C., and Amos, L. G., 1965, ASME J. Eng. Ind., 87, pp. 287–289)
(The American Society of Mechanical Engineers (ASME), 1965) -
1963 Review of Metal Processing Literature
(The American Society of Mechanical Engineers (ASME), 1965)By members of the Literature Review Committee of the ASME Metal Processing Research Activity: J. L. Wennberg, General Electric Company, Chairman ; B. F. von Turkovich, University of Illinois, ...