Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5841-5860 of 7723
-
Dynamic Peripheral Milling of Flexible Structures
(The American Society of Mechanical Engineers (ASME), 1992) -
Tool Temperatures in Interrupted Metal Cutting
(The American Society of Mechanical Engineers (ASME), 1992)This paper summarizes the results of theoretical and experimental studies of tool temperatures in interrupted cutting. In the theoretical study, the temperature in a semi-infinite rectangular ... -
Use of Audio Signals for Chatter Detection and Control
(The American Society of Mechanical Engineers (ASME), 1992)This paper compares various sensors and shows that a microphone is an excellent sensor to be used for chatter detection and control. Comparisons are made between the microphone and some other ... -
Design of Cellular Manufacturing Systems
(The American Society of Mechanical Engineers (ASME), 1992)This paper describes a method for layout design of a Cellular Manufacturing System (CMS) that would allow simultaneously, the grouping of machines unique to a part family into cells and those ... -
Friction Behavior in the Cup Ironing Process of Aluminum Sheets
(The American Society of Mechanical Engineers (ASME), 1992)The object of this paper is to clarity the surface flattening mechanism in the cup ironing process based on the lubricating mechanism. A new experimental apparatus for the ironing process was ... -
A Multi-Degree-of-Freedom Measuring System for CMM Geometric Errors
(The American Society of Mechanical Engineers (ASME), 1992) -
Modelling and Optimization of the NO Formation in an Industrial Glass Furnace
(The American Society of Mechanical Engineers (ASME), 1992)The effects of combustion excess-air level, air preheating, and fuel composition on the nitric oxide emissions from an industrial glass furnace are studied through the use of a mathematical ... -
Measurement of Grinding Temperature of Ceramics Using Infrared Radiation Pyrometer with Optical Fiber
(The American Society of Mechanical Engineers (ASME), 1992)The grinding temperature in the surface layer of a ceramic workpiece was measured using an IRP (infrared radiation pyrometer) connected by means of an optical fiber. Two types of optical fiber ... -
The Importance of the Application Sequence of Clamping Forces on Workpiece Accuracy
(The American Society of Mechanical Engineers (ASME), 1992)The effect of the application sequence of clamping forces on the mounting accuracy of a workpiece is investigated mathematically and experimentally. It is shown that clamping sequence causes a ... -
Error-Free Interpolation of Parametric Surfaces
(The American Society of Mechanical Engineers (ASME), 1992)A Digital Differential analyzer (DDA) is a cost effective implementation for interpolating parametric curves and surfaces. However, the problems of register overflow and integer round-off have ... -
Aspects of Process Model for Automatic Control of Edge-Deburring with Filamentary Brush
(The American Society of Mechanical Engineers (ASME), 1992)In this paper, process models are reported for a dynamic system consisting of a polymer/mineral abrasive filamentary brush during an orthogonal deburring operation. Dynamic process models are ... -
Threshold Stress Criterion in New Wheel/Rail Interaction for Limiting Rail Damage Under Heavy Axle Loads
(The American Society of Mechanical Engineers (ASME), 1992)This paper presents a qualitative discussion of the effects of increasing new (initial) wheel-rail contact stresses on the degree of damage to the rail due to heavy axle loads. The importance ... -
On the Wear Mechanisms and Cutting Performance of Silicon Carbide Whisker-Reinforced Alumina
(The American Society of Mechanical Engineers (ASME), 1992)The objective of this research was to study the types of wear suffered by silicon carbide whisker-reinforced aluminum oxide inserts in the machining of Inconel 718. Further, it was desired to ... -
Optimization of Multistage Machining Systems, Part 2: The Algorithm and Applications
(The American Society of Mechanical Engineers (ASME), 1992)In Part 1 of this paper [1], the basic form of a novel, optimization approach to utilize balance delay (idle) times within stations in a multistage machining system was introduced. In Part ... -
An Analysis of Void Deformation Caused by Power Law Creep and Diffusion Enhanced by Mechanical Stress in HIP Process
(The American Society of Mechanical Engineers (ASME), 1992)A dominant deformation mechanism in an isostatic pressure sintering process of a powder compact is known as power law creep. The deformation of a pore was predicted from the existing stress ... -
Processing of Cellular Polyurethane by Ultrasonic Excitation
(The American Society of Mechanical Engineers (ASME), 1992)Processing of cellular polyurethane was investigated experimentally and theoretically to examine the possibility of ultrasonic foaming. Polyol resin was supersaturated with nitrogen and ultrasonic ... -
A Study of Quenching: Experiment and Modelling
(The American Society of Mechanical Engineers (ASME), 1992)This paper describes the design, execution, mathematical modelling, and simulation of a simple, yet very useful quenching experiment—the asymmetric one-sided quenching of a beam. This experiment ... -
Optimization of Multistage Machining Systems, Part 1: Mathematical Solution
(The American Society of Mechanical Engineers (ASME), 1992)The optimization problem for multistage machining systems has been investigated. Due to uneven time requirements at different stages in manufacturing, there could be idle times at various stations. ... -
Design Analysis of a Twin Head Horizontal Hydraulic Press
(The American Society of Mechanical Engineers (ASME), 1992)Because of economical reasons, use of the single or multi-head hydraulic press is finding popularity in recent times in assembly work for automotive parts in particular. As this type of press ... -
On-Line Roundness Error Compensation via P-Integrator Learning Control
(The American Society of Mechanical Engineers (ASME), 1992)The work described is the result of a research project for developing a roundness error compensation scheme in turning processes based on the p-integrator learning controller and an on-line ...