Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5121-5140 of 7723
-
Critical Speeds of Rotating Shaft Subjected to Axial Loading and Tangential Torsion
(The American Society of Mechanical Engineers (ASME), 1967)In this study the classical theory of the bending and twisting of thin rods is utilized and applied to the case of a rotating shaft subjected to axial loading and tangential torsion. The ... -
Analysis of Residual, Thermal, and Loading Stresses in a B33 Wheel and Their Relationship to Fatigue Damage
(The American Society of Mechanical Engineers (ASME), 1967)The current General Electric computer study sponsored by The American Iron and Steel Institute, discussed at the ASME Railroad Division 1965 Winter Meeting, has the objective of determining the ... -
Report of Committee RR-6 Survey: Progress in Railway Mechanical Engineering, 1965–1966
(The American Society of Mechanical Engineers (ASME), 1967)This paper contains the annual report of the ASME Survey Committee RR-6. Developments in Railway Mechanical Engineering from September 1, 1965, to September 1, 1966, which pertain to railcars ... -
Four Multiply Separated Positions in Coplanar Motion
(The American Society of Mechanical Engineers (ASME), 1967)The combination of infinitesimally and finitely separated positions in coplanar kinematics is investigated. Each combination requires a separate analytical treatment based on the fundamental concepts ... -
Higher-Order Plane Motion Theories in Kinematic Synthesis
(The American Society of Mechanical Engineers (ASME), 1967)Algebraic multiple-position theories in kinematic synthesis are classified in a manner which also suggests various extensions of classical circular theory. In the case of infinitesimally separated ... -
Synthesis of Spherical Linkages With Use of the Displacement Matrix
(The American Society of Mechanical Engineers (ASME), 1967)Equations of synthesis are derived which are based upon rigid body motion expressed as a displacement matrix. Applications are shown in spherical rigid body guidance, function generation, and ... -
Synthesis of Plane Linkages With Use of the Displacement Matrix
(The American Society of Mechanical Engineers (ASME), 1967)A generalized matrix for the description of rigid body displacement in two dimensions is developed. This displacement matrix is applied to the synthesis of plane linkages used for rigid body ... -
Analog Simulation of Rigid Link Mechanisms
(The American Society of Mechanical Engineers (ASME), 1967)This paper describes a procedure for simulating rigid link mechanisms on an analog computer. The computer circuit enables one to record all kinematic variables, i.e., displacements, velocities, ... -
General Systematization and Unified Calculation of Five and Four-Bar Plane Basic Mechanisms
(The American Society of Mechanical Engineers (ASME), 1967)This paper is based on the use of complex harmonic series in the examination of plane mechanisms. Certain general considerations are established for the kinematic solving of binary structural ... -
Discussion: “Ultrasonic Grinding Economics” (Kaczmarek, J., Kops, L., and Shaw, M. C., 1966, ASME J. Eng. Ind., 88, pp. 449–454)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Report of Committee RR-6 Survey: Progress in Railway Mechanical Engineering, 1965–1966” (Bateson, N. E., Lich, R. L., and Baker, P. H., 1967, ASME J. Eng. Ind., 89, pp. 235–247)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Synthesis of Spherical Linkages With Use of the Displacement Matrix” (Suh, C. H., and Radcliffe, C. W., 1967, ASME J. Eng. Ind., 89, pp. 215–221)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Analog Simulation of Rigid Link Mechanisms” (Timm, R. F., 1967, ASME J. Eng. Ind., 89, pp. 199–204)
(The American Society of Mechanical Engineers (ASME), 1967) -
Rapid Filling of a Cylinder With a Compressible Fluid
(The American Society of Mechanical Engineers (ASME), 1967)A study was made of the temperatures in a cylindrical receiver resulting from rapid filling with a compressible fluid. The classical bottle-filling case was compared with the filling of a ... -
The Influence of Pressure Cycling on Thermal Regenerators
(The American Society of Mechanical Engineers (ASME), 1967)A theoretical and experimental investigation examines the performance of thermal regenerators in which rapid flow cycling is accompanied by large pressure variations with time. This class of ... -
Strain-Hardening and Strain-Rate Effects in Plastic Flow Through Conical Converging Dies
(The American Society of Mechanical Engineers (ASME), 1967)An upper-bound solution for energy expended to cause the flow of strain-hardening material through conical converging dies is presented. A linear strain-hardening coefficient is considered. The ... -
An Explanation of the Apparent Bridgman Effect in Merchant’s Orthogonal Cutting Results
(The American Society of Mechanical Engineers (ASME), 1967)In Merchant’s modified shear angle solution, it is assumed following Bridgman that the shear strength of the work material is a function of the hydrostatic stress. Although Merchant’s experimental ... -
Metal Cutting Analysis: Introduction to a New Theoretical Approach
(The American Society of Mechanical Engineers (ASME), 1967)In this work, the author develops a new approach to the theory of the cutting mechanism based on the comparative analysis of classical theories. He suggests the introduction of an empirical ... -
Thermal Analysis of Metal Flow at the Chip-Tool Interface in Metal Cutting
(The American Society of Mechanical Engineers (ASME), 1967)The plastic flow of metal adjacent to the chip-tool interface is analyzed using a mechanical equation of state, which relates the variables stress, strain, strain rate, and temperature. Expressions ... -
A New Approach to Determination of the Shear-Plane Angle in Machining
(The American Society of Mechanical Engineers (ASME), 1967)A reevaluation of the minimum-energy type of solution for shear-plane angle has been made, without reference to a coefficient of friction. It is proposed that the shear plane will be oriented ...