Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5101-5120 of 7723
-
Discussion: “Low-Cycle Fatigue of Large-Diameter Bolts” (Snow, A. L., and Langer, B. F., 1967, ASME J. Eng. Ind., 89, pp. 53–60)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “The Prediction of Pressure Loss During Two-Phase Horizontal Flow in Two-Inch Pipe” (Andrews, D. E., Knowles, Jr., C. R., Eaton, B. A., Silberberg, I. H., and Brown, K. E., 1967, ASME J. Eng. Ind., 89, pp. 44–51)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “The Free Vibrations of Stiffened Drill Strings With Static Curvature” (Frohrib, D. A., and Plunkett, R., 1967, ASME J. Eng. Ind., 89, pp. 23–29)
(The American Society of Mechanical Engineers (ASME), 1967) -
A New Explanation of the Phenomenon of Chip Curling During Machining
(The American Society of Mechanical Engineers (ASME), 1967)None of the existing explanations suggested by various research workers satisfactorily explains the various degrees of chip curl observed under different cutting conditions. A new explanation of ... -
Analysis of Plastic Flow Through Inclined Planes in Plane Strain
(The American Society of Mechanical Engineers (ASME), 1967)A wide strip of thickness t0 is pulled or extruded through inclined planes converging with semiangle α and exit gap tf . While passing through the die, the thickness of the strip changes ... -
Thermal Aspects of the Abrasive Cutoff Operation. Part 1—Theoretical Analysis
(The American Society of Mechanical Engineers (ASME), 1967)The heat transfer aspects of abrasive cutoff operation are investigated analytically. The analytical results lead to integral expressions for a dimensionless temperature of cutting interface as a ... -
Analysis of Oblique Cutting Forces
(The American Society of Mechanical Engineers (ASME), 1967)This paper is the latest of a continuing series on the subject of self-excited machine tool chatter. The representation of the metal cutting process as required by the previously developed ... -
Computer Application to the Visioplasticity Method
(The American Society of Mechanical Engineers (ASME), 1967)Procedures for using a computer for the complete solution to plane strain as well as axisymmetric deformation problems have been developed. The velocity, strain rate, total effective strain, and ... -
A Remote Sensor Method for Determining Average Tool-Chip Interface Temperatures in Metal Cutting
(The American Society of Mechanical Engineers (ASME), 1967)This paper shows the development of a mathematical model for determining the average interface temperatures when using a remote sensor. The accuracy of the remote sensor technique was greatly ... -
The Effect of Some Operating Variables in Vertical Spindle Abrasive Machining of Mild Steel
(The American Society of Mechanical Engineers (ASME), 1967)This paper reports the results of a systematic test program designed to determine the effect of work area, downfeed rate, and segment grade on performance on vertical spindle surface grinders. ... -
The Influence of Physical Properties on Penetration in Arc Welding
(The American Society of Mechanical Engineers (ASME), 1967)Simple butt welds were produced using a particular metal and a variety of combinations of current, voltage, and welding velocity. Four metals possessing quite different physical properties were ... -
The Effect of Experimental Error on the Determination of the Optimum Metal-Cutting Conditions
(The American Society of Mechanical Engineers (ASME), 1967)The effect of experimental error in tool life testing on the determination of the minimum cost cutting speed (Vmin ) is investigated by using the concept of statistical inference. It is shown ... -
Creative Design of Epicyclic Gear Trains Using Number Synthesis
(The American Society of Mechanical Engineers (ASME), 1967)The following paper applies the theory of number synthesis to the creative design of epicyclic gear trains. First, the associated linkage of an existing epicyclic gear train is derived as an ... -
The Analysis and Design of Hydraulic Pressure-Reducing Valves
(The American Society of Mechanical Engineers (ASME), 1967)This paper presents the static and dynamic characteristics of single-stage pressure-reducing valves and establishes design criteria. The dynamic analysis was accomplished using frequency-response ... -
Dynamic Coupling Effects in Rotary Face Seal Separation Phenomena
(The American Society of Mechanical Engineers (ASME), 1967)Dynamic separation phenomena in spring-supported rotary face seals are studied, employing a mathematical model which simulates the dynamic response characteristics of the system. Parameters considered ... -
Beating in Three-Mass Systems Under Step Velocity Input. Part 2—Experimental
(The American Society of Mechanical Engineers (ASME), 1967)An experimental study of the response of three-mass systems to step changes of the base velocity is described. Recordings that show the beating that can occur between the vibrations in two ... -
Beating in Three-Mass Systems Under Step Velocity Input. Part 1—Analytical
(The American Society of Mechanical Engineers (ASME), 1967)The response of three-mass systems to step changes of the base velocity is discussed. It is shown that beating, which may occur between the vibrations in two normal modes, can result in a ... -
Whirling of Shafts in Geared Systems
(The American Society of Mechanical Engineers (ASME), 1967)This paper presents a study on the effect of gear constraint on the whirl of simple-supported pinion shafts with and without overhung masses. A special tester capable of simulating the different ... -
In-Plane Bending of a Short-Radius Curved Pipe Bend
(The American Society of Mechanical Engineers (ASME), 1967)The analysis developed in this article is a logical extension, or generalization, of Von Karman’s original theory [1] on curved pipe bends. It can be shown, for long-radius pipe bends which ... -
Transient Thermal Stress and Associated Natural Frequency Variations in Circular Disk Elements
(The American Society of Mechanical Engineers (ASME), 1967)Most available thermal stress and associated natural frequency analyses of circular disk elements incorporate only the steady-state temperature distribution and intuitively assume that the transient ...