Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 3881-3900 of 7723
-
Solutions for Distributed Loads on Long Cylinders
(The American Society of Mechanical Engineers (ASME), 1969)Previously unavailable solutions of the elastic behavior of a long cylinder subjected to balanced radial loads are obtained. The circumferentially distributed radial load solution is extended to ... -
Modeling Cutting: Plastic Deformation of Polymer Samples Indented With a Wedge
(The American Society of Mechanical Engineers (ASME), 2007)An experiment was designed to relate force to plastic deformation caused by a wedge indenting the edge surface of a polymer sample. The experiment reveals the primary phenomena observed in ... -
Stream-of-Variation (SOVA) Modeling II: A Generic 3D Variation Model for Rigid Body Assembly in Multistation Assembly Processes
(The American Society of Mechanical Engineers (ASME), 2007)A 3D rigid assembly modeling technique is developed for stream of variation analysis (SOVA) in multi-station processes. An assembly process is modeled as a spatial indexed state transition dynamic ... -
Response of Thin Films and Substrate to Micro-Scale Laser Shock Peening
(The American Society of Mechanical Engineers (ASME), 2007)Micro-scale laser shock peening (μLSP) can potentially be applied to metallic structures in microdevices to improve fatigue and reliability performance. Copper thin films on a single-crystal silicon ... -
Ultrasonic Cavitation Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites
(The American Society of Mechanical Engineers (ASME), 2007)Lightweight metal–matrix nanocomposites (MMNCs) (metal matrix with nanosized ceramic particles) can be of significance for automobile, aerospace, and numerous other applications. It would be ... -
Model-Based Analysis of the Surface Generation in Microendmilling—Part II: Experimental Validation and Analysis
(The American Society of Mechanical Engineers (ASME), 2007)The surface-generation models for the microendmilling process developed in Part I (, , and , 2007, J. Manuf. Sci. Eng., 129(3), pp. 453–460) are experimentally calibrated and validated. Partial ... -
Analytical and Experimental Study of Determining the Optimal Number of Wedge Shape Cutting Teeth in Coring Bits Used in Percussive Drilling
(The American Society of Mechanical Engineers (ASME), 2007)In this paper we study the design of the coring bits with wedge-shape cutting teeth of vibratory drills that percussively penetrate into brittle material. The overall coring bit specific energy ... -
Axisymmetric, Nonidentical, Flat Face Flanges With Metal-to-Metal Contact Beyond the Bolt Circle
(The American Society of Mechanical Engineers (ASME), 1969)A method of analyzing a pair of nonidentical, axisymmetric flat face flanges with metal-to-metal contact beyond the bolt circle is described. The design method takes into account interaction ... -
Finite Element Analysis of Solidification in Rapid Freeze Prototyping
(The American Society of Mechanical Engineers (ASME), 2007)Rapid freeze prototyping (RFP) can generate three-dimensional ice patterns from computer-aided design (CAD) models by depositing and solidifying water droplets layer by layer. One important issue ... -
Tool Temperature in Titanium Drilling
(The American Society of Mechanical Engineers (ASME), 2007)The spatial and temporal distribution of tool temperature in drilling of commercially pure titanium is studied using the inverse heat transfer method. The chisel and cutting edges of a spiral ... -
Directionally Independent Failure Prediction of End-Milling Tools During Pocketing Maneuvers
(The American Society of Mechanical Engineers (ASME), 2007)Tracking the health of cutting tools under typical wear conditions is advantageous to the speed and efficiency of manufacturing processes. Existing techniques monitor tool performance through ... -
Process-Driven Input Profiling for Plastics Processing
(The American Society of Mechanical Engineers (ASME), 2007)Most plastic processing set points are variables that need to be defined for each sample point of the cycle. However, in the absence of on-line measures of part quality, the set points cannot ... -
Investigation of the Tooth Geometry of a Hob for Machining of Involute Gears (in the Tool-in-Use Reference System)
(The American Society of Mechanical Engineers (ASME), 2007)This paper is aiming at development of an analytical approach for computation of the geometrical parameters of cutting edges of an involute hob. It is well recognized that the involute hob ... -
Dynamic Hybrid Modeling of the Vertical Z Axis in a High-Speed Machining Center: Towards Virtual Machining
(The American Society of Mechanical Engineers (ASME), 2007)This paper describes the modeling and simulation of the Z axis of a five axis machining center for high-speed milling. The axis consists of a mechanical structure: machine head and electro-mandrel, ... -
Systematic Modeling of Workpiece-Fixture Geometric Default and Compliance for the Prediction of Workpiece Machining Error
(The American Society of Mechanical Engineers (ASME), 2007)Control of workpiece machining error (WME) is a key concern in the design of a fixture system. In this paper, source errors, which are categorized into workpiece-fixture geometric default and ... -
Stream-of-Variation Modeling—Part I: A Generic Three-Dimensional Variation Model for Rigid-Body Assembly in Single Station Assembly Processes
(The American Society of Mechanical Engineers (ASME), 2007)A stream-of-variation analysis (SOVA) model for three-dimensional (3D) rigid-body assemblies in a single station is developed. Both product and process information, such as part and fixture locating ... -
Modeling and Control of a New Robotic Deburring System
(The American Society of Mechanical Engineers (ASME), 2007)This paper discusses the modeling and control of a robotic manipulator with a new deburring tool, which integrates two pneumatic actuators to take advantage of a double cutting action. A ... -
Local Flexibility Coefficients for the Built-In Ends of Beams and Plates
(The American Society of Mechanical Engineers (ASME), 1969)The usual methods of structural analysis (including most modern computer methods) are based on the assumption that cross sections remain plane. Consequently local flexibilities at structural ... -
Analytical Modeling of Chatter Stability in Turning and Boring Operations—Part I: Model Development
(The American Society of Mechanical Engineers (ASME), 2007)In this paper an analytical model for stability limit predictions in turning and boring operations is proposed. The multidimensional model includes the three-dimensional geometry of the processes ... -
Study of the Size Effects and Friction Conditions in Microextrusion—Part II: Size Effect in Dynamic Friction for Brass-Steel Pairs
(The American Society of Mechanical Engineers (ASME), 2007)In this paper, the results of experiments conducted to investigate the friction coefficient existing at a brass-steel interface are presented. The research discussed here is the second of a ...