Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 3861-3880 of 7723
-
A Dynamic Sensing-and-Modeling Approach to Three-Dimensional Point- and Area-Sensor Integration
(The American Society of Mechanical Engineers (ASME), 2007)The recent advancement of 3D non-contact laser scanners enables fast measurement of parts by generating a huge amount of coordinate data for a large surface area in a short time. In contrast, ... -
Building a Mathematical Model to Predict Transient Drilling Temperature Responses
(The American Society of Mechanical Engineers (ASME), 1969)A transient drilling temperature predicting equation is developed using a statistical model-building technique. The functional form of the model is obtained by combining both theoretical considerations ... -
Surface Modification and Fatigue Behavior of High-Pressure Oil Jet-Peened Medium Carbon Steel, AISI 1040
(The American Society of Mechanical Engineers (ASME), 2007)Introduction of compressive residual stresses on the fatigue-loaded components is one of the techniques followed to improve the fatigue life of industrial components. Oil jet peening is a surface ... -
Variation Simulation of Sheet Metal Assemblies Using the Method of Influence Coefficients With Contact Modeling
(The American Society of Mechanical Engineers (ASME), 2007)Sheet metal assembly is a common assembly process for several products such as automobiles and airplanes. Since all manufacturing processes are affected by variation, and products need to have ... -
Supervisory Factory Control Based on Real-Time Production Feedback
(The American Society of Mechanical Engineers (ASME), 2007)One key characteristic of any process performance is variability; that is, a process rarely performs consistently over time. The bottleneck is one of the main reasons causing the system variability ... -
Inspection of White Layer in Hard Turned Components Using Electrochemical Methods
(The American Society of Mechanical Engineers (ASME), 2007)This paper presents the results of electrochemical tests on hard turned steel components that have white layer on the surface. Electrochemical impedance spectroscopy is used to compare a machined ... -
An Evaluation of ASME Ellipsoidal Heads
(The American Society of Mechanical Engineers (ASME), 1969)The ASME Code specifications for unfired cylindrical pressure vessels are examined from the viewpoint of the lower bound theorem of limit analysis. The problem is formulated as a linear programming ... -
A Time Domain Dynamic Simulation Model for Stability Prediction of Infeed Centerless Grinding Processes
(The American Society of Mechanical Engineers (ASME), 2007)This paper presents a comprehensive dynamic model that simulates infeed centerless grinding processes and predicts their instability-related characteristics. The new model has the unique ability ... -
Modeling and Prediction of Cutting Noise in the Face-Milling Process
(The American Society of Mechanical Engineers (ASME), 2007)A cutting noise prediction model is developed to relate the cutter-workpiece vibrations to the sound pressure field around the cutter in the high-speed face-milling process. The cutter-workpiece ... -
Investigation to Study the Applicability of Solid Lubricant in Turning AISI 1040 steel
(The American Society of Mechanical Engineers (ASME), 2007)Machining of materials has received substantial attention due to the increasing use of machining processes in various industrial applications. The research in this area is intended mainly to ... -
Virtual Clay: An Enhanced Marching Cubes Algorithm for In-Process Geometry Modeling
(The American Society of Mechanical Engineers (ASME), 2007)This paper presents an enhanced marching cubes algorithm to construct an iso-boundary for in-process geometric modeling for material removal processes. The author first analyzes the tool motion ... -
Thermo-Mechanical Finite Element Modeling of the Friction Drilling Process
(The American Society of Mechanical Engineers (ASME), 2007)Friction drilling uses a rotating conical tool to penetrate the workpiece and create a bushing in a single step without generating chips. This research investigates the three-dimensional (3D) ... -
The Effect of Nonconventional Laser Beam Geometries on Stress Distribution and Distortions in Laser Bending of Tubes
(The American Society of Mechanical Engineers (ASME), 2007)Laser forming is a spring-back-free noncontact forming method that has received considerable attention in recent years. Compared to mechanical bending, no hard tooling, dies, or external force ... -
Predictive Modeling of Flank Wear in Turning Under Flood Cooling
(The American Society of Mechanical Engineers (ASME), 2007)The objective of this paper is to present physical and quantitative models for the rate of tool flank wear in turning under flood cooling conditions. The resulting models can serve as a basis ... -
Three-Dimensional Modeling of Laser Sintering of a Two-Component Metal Powder Layer on Top of Sintered Layers
(The American Society of Mechanical Engineers (ASME), 2007)A three-dimensional model of selective laser sintering of a two-component loose metal powder layer on top of previously sintered layers by a single-line laser scanning is presented. A ... -
Laser Direct-Part Marking of Data Matrix Symbols on Carbon Steel Substrates
(The American Society of Mechanical Engineers (ASME), 2007)Certain applications have recently appeared in industry where a traditional bar code printed on a label will not survive because the item to be tracked has to be exposed to harsh environments. ... -
Reconfigurable Pin-Type Tooling: A Survey of Prior Art and Reduction to Practice
(The American Society of Mechanical Engineers (ASME), 2007)The idea of using a bed-of-pins as a completely reconfigurable discrete tool surface (referred to as a reconfigurable pin-type tool) for forming or molding of mechanical components has been ... -
Lapping of Electrical Discharge Machining Processed Tool Steel Surface Using Elliptical Tool Motion
(The American Society of Mechanical Engineers (ASME), 2007)A prototype lapping machine, which finishes surfaces by applying elliptical motions to a lapping tool in the presence of diamond compound, is developed. This paper describes the structure of ... -
Model-Based Analysis of the Surface Generation in Microendmilling—Part I: Model Development
(The American Society of Mechanical Engineers (ASME), 2007)This paper presents the development of models that describe the surface-generation process for microendmilling. The surface-generation models for the sidewall and floor surfaces consist of deterministic ... -
Modeling of the Size Effects on the Behavior of Metals in Microscale Deformation Processes
(The American Society of Mechanical Engineers (ASME), 2007)For the accurate analysis and design of microforming process, proper modeling of material behavior at the micro/mesoscale is necessary by considering the size effects. Two size effects are known ...