Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1841-1860 of 7723
-
Discussion: “Cutting Fluids Performance” (Nagpal, B. K., and Sharma, C. S., 1973, ASME J. Eng. Ind., 95, pp. 881–889)
(The American Society of Mechanical Engineers (ASME), 1974) -
On Chatter Vibrations of Machine Tool or Work Due to Regenerative Effect and Time Lag
(The American Society of Mechanical Engineers (ASME), 1974)This paper treats the most general chatter vibrations of machine tool or work originating by regenerative effect having an arbitrary overlap factor, by wave cutting effect (time lag of thrust ... -
Shear Angle Relationship With Variable Undeformed Chip Thickness
(The American Society of Mechanical Engineers (ASME), 1974)Effect of surface slope of the workpiece on shear angle has been considered by applying Hill’s [1] deformation criteria to the triangular shear zone in orthogonal metal-cutting process with ... -
Rotor Resonant Speed Reduction Caused by Flexibility of Disks
(The American Society of Mechanical Engineers (ASME), 1974)An analysis is developed to include the effect of disk flexibility and gyroscopic forces on the resonant frequencies of an axisymetric rotating shaft with multiple disks and bearings. The shaft ... -
The Formation of Oxycarbides During the Oxide Treatment of Cemented Carbide Tools
(The American Society of Mechanical Engineers (ASME), 1974)Reactions between oxides and carbides were investigated in order to establish enhancement mechanisms occurring during the oxide treatment of cemented carbide tools. TiO powder was compacted around ... -
A Study of the Strain Distributions and Strain Histories in Axisymmetrical Stretch-Forming
(The American Society of Mechanical Engineers (ASME), 1974)The strain distributions and strain histories in the axisymmetrical sheet metal forming process have hitherto been difficult to study owing to the lack of a succinct system of representation. ... -
Recovery of Modal Information From a Beam Undergoing Random Vibration
(The American Society of Mechanical Engineers (ASME), 1974)An organized approach for implementing the techniques of random process theory in the recovery of structural information from random vibration data is presented. The boundaries of various configured ... -
Dynamics of Eccentric Shafts Under Linearly Varying Tension Rotating in a Viscous Medium
(The American Society of Mechanical Engineers (ASME), 1974)Using Euler-Bernoulli beam theory an investigation is made of the dynamic behavior of an eccentric vertical circular shaft rotating in viscous medium. The shaft is subjected to linearly-varying ... -
Examination of the Response of a Flexible Circular Rotor Subjected to Specified Gyroscopic Rates
(The American Society of Mechanical Engineers (ASME), 1974)The natural and forced motion of a rotor configuration comprised of a constant thickness, annular plate fixed at the inner boundary to a rigid core and at the outer boundary to a symmetric, ... -
Buckling of Circular Cylindrical Shells Using a Displacement Function
(The American Society of Mechanical Engineers (ASME), 1974)The buckling problem of circular cylindrical shells under axial compression, external pressure, and torsion is investigated using a displacement function φ. A governing differential equation for ... -
Practices in Operational Management—Personnel Management
(The American Society of Mechanical Engineers (ASME), 1961) -
Optimum Design of Four-Bar Crank Mechanisms With Prescribed Extreme Velocity Ratios
(The American Society of Mechanical Engineers (ASME), 1974)The design of four-bar crank mechanisms to have prescribed maximum and minimum angular velocity ratios is treated. The mechanisms are optimized by minimizing their maximum pressure angles. Two ... -
On Probabilistic Design
(The American Society of Mechanical Engineers (ASME), 1974)The probabilistic approach to design is developed and contrasted with the conventional safety factor approach. A careful interpretation of random variable design inputs is given, leading to a ... -
Optimization of Tension Level and Stinger Length for Offshore Pipeline Installation
(The American Society of Mechanical Engineers (ASME), 1974)Offshore pipelines have been installed for a period of some 10 to 20 years using a variety of methods. This paper presents a new analysis method for the optimization of certain operation ... -
Free Machining Steels—The Behavior of Type I MnS Inclusions in Machining
(The American Society of Mechanical Engineers (ASME), 1974)Experimental results obtained by in situ machining within a Scanning Electron Microscope of a resulphurized steel containing Type I manganese sulphide inclusions are presented. The data obtained ... -
Determination of Geometric Properties of Coated Abrasive Cutting Edges
(The American Society of Mechanical Engineers (ASME), 1974)The surface topography of a coated abrasive was measured by a special designed profilometer with an oscillating stylus, revealing very detailed geometric features of the peaks. The criterion for ... -
Analysis of Thermal Expansion in Face-Cutting Operations
(The American Society of Mechanical Engineers (ASME), 1974)Theoretical and experimental analyses are developed for the thermal expansion of a tool and a cylindrical work during face-cutting with a lathe. Theoretical investigation considers temperature ... -
A Study of the Drilling Process
(The American Society of Mechanical Engineers (ASME), 1974)Drilling is a complex three dimensional cutting process yet it is possible to simulate the action of a two flute twist drill with two dimensional models provided consideration is given to the ... -
Machine Tool Chatter: Effect of Surface Slope on Machining Forces During Wave Removing
(The American Society of Mechanical Engineers (ASME), 1974)The effect of work surface slope (rate of change of undeformed chip thickness) on machining forces has been measured. The results of these experiments are used to develop equations for the ... -
Thermal Analysis of the Wear of Single Abrasive Grains
(The American Society of Mechanical Engineers (ASME), 1974)It is shown that the wear of single abrasive grains in a simulated grinding operation (over-cut fly milling) is governed by a thermally activated mechanism. The model adopted in this theoretical ...