Journal of Pressure Vessel Technology: Recent submissions
Now showing items 4261-4280 of 4506
-
Stratapax Drill Bit for Gulf Coast Drilling
(The American Society of Mechanical Engineers (ASME), 1978)A drill bit employing GE Stratapax drill blanks has been developed for Gulf Coast drilling. Single point cutting tests demonstrated superior impact qualities of Stratapax when compared to natural ... -
Discussion: “Fatigue Design Criterion for Pressure Vessel Alloys” (Jaske, C. E., and O’Donnell, W. J., 1977, ASME J. Pressure Vessel Technol., 99, pp. 584–592)
(The American Society of Mechanical Engineers (ASME), 1978) -
The Background of ASME Code Case 1828: A Simplified Method of Analyzing Part B Flanges
(The American Society of Mechanical Engineers (ASME), 1978)The 1974 Edition of ASME Boiler and Pressure Vessel Code Section VIII, Division 1, provides rules for the analysis and design of identical pairs of Part B flanges (flat face flanges in ... -
Stress Intensity Factors for Reactor Vessel Nozzle Cracks
(The American Society of Mechanical Engineers (ASME), 1978)A method consisting of a marriage between frozen stress photoelasticity and a computerized least-squares data analysis for extracting stress intensity factor (SIF) distributions in three-dimensional ... -
An Assessment of Overburden Stability in the In-Situ Gasification of Texas Lignite
(The American Society of Mechanical Engineers (ASME), 1978)In-situ gasification can be competitive with shaft mining for the exploitation of coal at depths too deep for surface mining. The lignite deposits in Texas may be well suited to this process ... -
Stresses in Ruptured Floating Roofs
(The American Society of Mechanical Engineers (ASME), 1978)Procedures are developed for determining the stresses and displacements for pontoon-type floating roof structures subjected to the loading caused by the product leaking through punctures onto the ... -
The Past, Present and Future of Section X of the ASME Boiler and Pressure Vessel Code
(The American Society of Mechanical Engineers (ASME), 1978) -
The Forces on a Cylinder Oscillating Sinusoidally in Water: Further Experiments
(The American Society of Mechanical Engineers (ASME), 1978)This paper deals with wave forces on a single cylinder. The wave forces are simulated in a laboratory by oscillating a cylinder sinusoidally in water otherwise at rest. This effort is a ... -
Design Curves for Stress Analysis of U-Tube Heat Exchanger Tubesheet With Integral Channel and Head
(The American Society of Mechanical Engineers (ASME), 1978)A U-tube heat exchanger with integral channel, head and unperforated rim is investigated to establish design rules based on application of elastic plate theory. The effect of tube bending ... -
Pile Foundations in Frozen Soils
(The American Society of Mechanical Engineers (ASME), 1978)A design philosophy for pile foundations in frozen soils is presented whereby seven different pile types may be used in different frozen subsoil conditions. The mechanics of frozen ground as ... -
Three-Dimensional Versus Axisymmetric Finite-Element Analysis of a Cylindrical Vessel Inlet Nozzle Subject to Internal Pressure—A Comparative Study
(The American Society of Mechanical Engineers (ASME), 1978)This paper presents a comparative study between a three-dimensional and an axisymmetric finite-element analysis of a reactor pressure-vessel inlet nozzle subject to internal pressure. A quarter-symmetric ... -
Geometry of Scalloped Closures for Cylindrical Vessels
(The American Society of Mechanical Engineers (ASME), 1978)Conical closures for cylindrical tanks are easily fabricated and hence would be economical if not for the large stresses developed at the sharp-cornered junction between cylinder and cone, ... -
Discussion: “Loading Mechanisms in Thawed Permafrost Around Arctic Wells” (Goodman, M. A., 1977, ASME J. Pressure Vessel Technol., 99, pp. 641–645)
(The American Society of Mechanical Engineers (ASME), 1978) -
Stiffness Coefficients and Allowable Loads for Nozzles in Flat-Bottom Storage Tanks
(The American Society of Mechanical Engineers (ASME), 1978)The stiffness coefficients presented in this paper simulate the actual local translational and flexural restraint of the nozzle connection due to the attached tank shell. These coefficients can ... -
Diamond Compact Cutter Studies for Geothermal Bit Design
(The American Society of Mechanical Engineers (ASME), 1978)As a prerequisite to design of a geothermal drill bit using diamond compact cutters, the rock cutting characteristics of these compacts have been studied in a series of instrumented single-cutter ... -
High Temperature Properties and Constitutive Equations for 1 Cr-1/2 Mo Steel
(The American Society of Mechanical Engineers (ASME), 1978)This paper presents the tensile, creep, rupture, and fatigue properties of 1 Cr-1/2 Mo steel. Tensile tests were conducted over a temperature range of 70–1150 F (21 to 621 C). Creep-rupture ... -
Structural Design for a 10-GWh SMES Vacuum Vessel
(The American Society of Mechanical Engineers (ASME), 1978)An approximate solution to the problem of the nonlinear elastic deformation of a periodically point-supported cylindrical shell is obtained. This solution is used to investigate the structural ... -
Rational and Economical Multicomponent Seismic Design of Piping Systems
(The American Society of Mechanical Engineers (ASME), 1978)The seismic analysis of complex piping systems is often carried out by the response spectrum method. The maximum probable responses are calculated as the square root of the sum of the squares ... -
Mechanical Behavior of Nonlinear Visco-Elastic Celluloid Under Superimposed Hydrostatic Pressure
(The American Society of Mechanical Engineers (ASME), 1978)The behavior of polymers is significantly influenced by hydrostatic pressure. In this paper, the effects of hydrostatic pressure and the third invariant of the deviatoric stress tensor on the ... -
Rules for Inservice Inspection for Nuclear Power Plant Components
(The American Society of Mechanical Engineers (ASME), 1978)