Journal of Pressure Vessel Technology: Recent submissions
Now showing items 4281-4300 of 4506
-
Design of U-Shaped Bellows Considering Low-Cycle Fatigue
(The American Society of Mechanical Engineers (ASME), 1978)The elastoplastic analysis for shells of revolution is applied to the problem of the U-shaped bellows subjected to completely reversed cyclic axial force. Use of these results together with the ... -
A Finite-Element Model for Residual Stresses and Deflections in Girth-Butt Welded Pipes
(The American Society of Mechanical Engineers (ASME), 1978)Computational models for predicting transient temperature distributions, residual stresses, and residual deflections for girth-butt welds are described. Comparisons of predicted and measured temperatures ... -
Deformation of Polymers During Hydrostatic Extrusion
(The American Society of Mechanical Engineers (ASME), 1978)Crystalline as well as amorphous polymers and a thermosetting resin were hydrostatically extruded with pressures up to 4 kilobars. A linear relation was obtained between the extrusion pressure ... -
Fluid Flow and Heat Transfer Through Hydraulically Induced Fractures in Hot, Dry Rock Masses
(The American Society of Mechanical Engineers (ASME), 1978)Geothermal energy extraction from hot, dry rock requires the circulation of water under pressure through a crack with a small opening (several millimeters) and a large radius (several hundred ... -
Bursting Pressure as the Basis for Cylinder Design
(The American Society of Mechanical Engineers (ASME), 1978)This paper gives a brief account of the developments carried out in the Northwich, England, laboratories of Imperial Chemical Industries Limited (ICI) which led to this method of design being ... -
Status ASME XI Appendix A—Evaluation of Flaw Indications
(The American Society of Mechanical Engineers (ASME), 1978) -
Elastic and Elastic-Plastic Buckling of Internally Pressurized 2:1 Ellipsoidal Shells
(The American Society of Mechanical Engineers (ASME), 1978)Elastic and elastic-plastic buckling pressures for internally-pressurized 2:1 ellipsoidal shells with diameter-thickness ratios in the range 750 < D/t < 1500 are given in the paper. The ... -
Failure Analysis of Steam Generator Tubes With Dented and Wastage Configurations
(The American Society of Mechanical Engineers (ASME), 1978)The occurrence of PWR steam generator tube cracking, denting, and wastage has been reported in the recent literature [1–5]. As indicated by its title, this paper concerns itself with the ... -
Analysis of Elastic-Plastic Plates and Shells Under Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1978)The behavior of elastic-plastic plate and shell structures under repeated loading is considered. The typical problem is formulated in incremental or “rate” form, and a variational method is ... -
Power Suppliers Need Nuclear
(The American Society of Mechanical Engineers (ASME), 1978) -
Influence of Inner Surface Defects on the Fatigue Strength of Pipe Subjected to Cyclic Internal Pressure
(The American Society of Mechanical Engineers (ASME), 1978)Cyclic internal oil pressure fatigue tests were carried out on medium-diameter ERW pipes of API 5LX - X60 in an attempt to determine the influence of surface defects on the fatigue strength. ... -
Reduction of Stress Concentration Due to Interference Fits in an Infinite Plate With Two Holes
(The American Society of Mechanical Engineers (ASME), 1978)This paper contains an exact solution for stresses which are produced in an infinite plate with two holes of different sizes by interference fits. It is assumed that the plate and the ... -
Normal Mode Solution of Fluid-Coupled Concentric Cylindrical Vessels
(The American Society of Mechanical Engineers (ASME), 1978)A normal mode solution is developed for concentric cylinders coupled by fluid between them and subjected to foundation input motion. Both time-history and spectral inputs can be specified. Example ... -
Pressure Tubes: The Pressure Vessels in the CANDU Nuclear Power Reactor
(The American Society of Mechanical Engineers (ASME), 1978)One of the main engineering characteristics of the CANDU nuclear power reactor is the use of pressure tubes rather than one large pressure vessel to contain the fuel and coolant. The power ... -
Special Publications
(The American Society of Mechanical Engineers (ASME), 1977) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1977) -
Special Publications
(The American Society of Mechanical Engineers (ASME), 1977) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1977) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1977) -
Some Field Permeation Properties of Fractured Permian and Triassic Sandstones in Northwest England
(The American Society of Mechanical Engineers (ASME), 1977)The 1000 m thick series of Permian and Triassic sandstones in Northwest England exhibit both intergranular and fissure flow. However, estimates of their relative importance can be distorted by ...