Journal of Pressure Vessel Technology: Recent submissions
Now showing items 4001-4020 of 4506
-
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1982) -
Strain Rate Effects in SA-106 Carbon Steel Pipe
(The American Society of Mechanical Engineers (ASME), 1982)Experiments were performed to measure the effect of strain rate on the tensile properties of SA-106 carbon steel pipe, in support of analysis and experimental modeling of postulated pipe whip ... -
A Survey of Studies Into the Hydrodynamic Response of Fluid-Coupled Circular Cylinders
(The American Society of Mechanical Engineers (ASME), 1982) -
A Finite Element Time Integration Method for the Theory of Viscoplasticity Based on Infinitesimal Total Strain
(The American Society of Mechanical Engineers (ASME), 1982)A forward gradient method is employed in the formulation of a time integration scheme for the theory of viscoplasticity based on total strain. The theory uses a viscosity function and an ... -
Full Life Elastic-Plastic-Creep Analysis and Comparison to Tests of Axially Cycled Pressurized Tubular Specimens
(The American Society of Mechanical Engineers (ASME), 1982)Full life elastic-plastic-creep analyses of axially cycled pressurized tubular 316H stainless steel and Incoloy 800 specimens were run in order to evaluate creep ratcheting and creep fatigue ... -
Effect of Tube Banks on Rarefaction Wave Propagation
(The American Society of Mechanical Engineers (ASME), 1982)In a continuing effort to study the effect of steam generator feed line break on steam generator internals, a theoretical and experimental study has been undertaken. This paper summarizes results ... -
Biaxial Cyclic Deformation and Creep-Fatigue Behavior of Materials for Solar Thermal Systems
(The American Society of Mechanical Engineers (ASME), 1982)Biaxial cyclic deformation and creep-fatigue data for Incoloy 800 and Type 316H stainless steel at elevated temperature are presented. Tubular specimens were subjected to constant internal pressure ... -
Influence of Service Exposure on Base and Weld Metal of 1/2 Cr-1/2 Mo-1/4 V High-Pressure Steam Inlet Piping
(The American Society of Mechanical Engineers (ASME), 1982)An investigation was performed on a circumferential weld joint in a 1/2 Cr-1/2 Mo-1/4 V high-pressure steam inlet pipe following the detection of steam leakage in a weld area. The component, ... -
Fatigue Design in Mining Size Reduction Equipment
(The American Society of Mechanical Engineers (ASME), 1982)The mining size reduction equipment industry is reviewed regarding efforts to obtain a consistent fatigue design philosophy. Serious structural failures, which have prompted various company efforts ... -
Dynamic Buckling of Inelastic Spherical Shells
(The American Society of Mechanical Engineers (ASME), 1982)The dynamic buckling behavior of a complete spherical shell made of a bilinear or work-hardening material and under a uniform external impulsive loading is investigated. A quasi-bifurcation theory ... -
Stress Analysis and Stress Index Development for a Trunnion Pipe Support
(The American Society of Mechanical Engineers (ASME), 1982)A finite element stress analysis is presented of a trunnion pipe anchor. The structure is analyzed for the case of internal pressure and various end moment loadings. Stress results were ... -
A Method for Determining Residual Stresses in Pipes
(The American Society of Mechanical Engineers (ASME), 1982)A combined analytical and experimental method for inferring the residual stresses in a pipe formed by joining two sections with a girth butt weld is described. The relieved surface strains due ... -
The Accumulation of Damage in Plates Subjected to Steady Mechanical Load and Cyclic Thermal Downshocks on One Surface
(The American Society of Mechanical Engineers (ASME), 1982)Computer calculations, incorporating analysis of elastic, plastic and creep effects, are performed on a Bree plate subjected to steady mechanical load and cyclic thermal downshocks on one surface. ... -
The Accumulation of Damage in Plates Subjected to Steady Mechanical Load and Cyclic Thermal Downshocks on Both Surfaces
(The American Society of Mechanical Engineers (ASME), 1982)Previously reported computations are extended to analyze a Bree plate subjected to steady mechanical load and cyclic thermal downshocks on both surfaces. It is shown that two critical plate ... -
Residual Stresses and Their Redistribution During Annealing of a Girth-Butt Welded Thin-Walled Pipe
(The American Society of Mechanical Engineers (ASME), 1982)The redistribution of calculated welding stresses during different post weld heat treatments (PWHT) is numerically investigated for a girth-butt welded thin-walled pipe made of a micro-alloyed ... -
Analytical Failure Prediction of Spherical Composite Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1982)The geometrical complexity of winding patterns for fiber composite spherical pressure vessels has most often resulted in design and analysis based on use of assumed spherical symmetry. Development ... -
Plastic Buckling of Various Shells
(The American Society of Mechanical Engineers (ASME), 1982)The phenomenon of plastic buckling is first illustrated by the behavior of a fairly thick cylindrical shell, which under axial compression deforms at first axisymmetrically and later nonaxisymmetrically. ... -
Numerical Analysis of Thermal Stresses During Welding Including Phase Transformation Effects
(The American Society of Mechanical Engineers (ASME), 1982)The problem of determining temperature distributions, transient thermal strains, and residual stresses during butt welding thick plates with the multipass GMAW process is solved using the finite ... -
The Effect of Time and Temperature on Residual Stresses in Austenitic Welds
(The American Society of Mechanical Engineers (ASME), 1982)The influence of heat treatment, upon residual stresses in AISI 316-type welds, is studied by subjecting a number of highly restrained weldments to various heat treatment cycles. Measurements ... -
Stiffening Effects on Thin-Walled Piping Elbows of Adjacent Piping and Nozzle Constraints
(The American Society of Mechanical Engineers (ASME), 1982)Elbows, attached to component nozzles or adjacent piping, experience a stiffening effect due to the restraint of ovalization provided by the nozzle or pipe. Using the thin-shell, finite difference ...