Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3981-4000 of 4506
-
Nonlinear Bending and Collapse Analyses of a Poked Cylinder and Other Point-Loaded Cylinders
(The American Society of Mechanical Engineers (ASME), 1983)Numerical results based on the STAGSC-1 finite element computer program are presented for the geometrically nonlinear behavior of cylindrical shells subjected to inward-directed radial point loads. ... -
Heat-to-Heat Variations in Creep-Rupture Properties of Annealed 2 1/4 Cr-1 Mo Steel
(The American Society of Mechanical Engineers (ASME), 1983)The creep and creep-rupture properties of 13 heats of annealed 2 1/4 Cr-1 Mo steel were determined at 510 and 566°C (950 and 1050°F). The microstructures of all heats were primarily ... -
Maximum Stresses and Flexibility Factors of Smooth Pipe Bends With Tangent Pipe Terminations Under In-Plane Bending
(The American Society of Mechanical Engineers (ASME), 1983)A theoretical solution is presented for the in-plane bending, linear elastic behavior of smooth, circular cross-sectional constant thickness pipe bends with connected tangent pipes of similar ... -
Experimental Buckling Investigation of Ring-Stiffened Cylindrical Shells Under Unsymmetrical Axial Loads
(The American Society of Mechanical Engineers (ASME), 1983)Six steel shells having nuclear containmentlike features were fabricated and loaded to failure with an offset axial load. The shells (R /t = 500) buckled plastically. Four of the shells had ... -
Membrane Theory for Layered Ellipsoidal Shells
(The American Society of Mechanical Engineers (ASME), 1983)The stress analysis of a laminated anisotropic ellipsoidal membrane shell of revolution is considered. A system of equations which is appropriate to the elastic behavior of anisotropic membrane ... -
Added Mass for Beam Mode Response
(The American Society of Mechanical Engineers (ASME), 1983)In 1972 a method was presented for evaluating the added mass of fluid contained between two long co-axial cylinders. The resulting equations have been widely quoted in the literature, and the ... -
Editor’s Pages
(The American Society of Mechanical Engineers (ASME), 1983) -
Stress Intensity Factor Solutions for Internal Longitudinal Semi-Circular Surface Flaws in a Cylinder Under Arbitrary Loading
(The American Society of Mechanical Engineers (ASME), 1983)The behavior of semi-circular surface flaws in cylinders is of interest in the technology of pressure vessels. The object of this study is to determine the stress intensity factor distribution ... -
Elastic-Plastic Analysis of Crack Opening, Stable Growth and Instability Behavior in Flawed 304 SS Piping
(The American Society of Mechanical Engineers (ASME), 1983)Crack initiation, stable growth, instability and crack opening behavior in flawed 304 SS piping has been examined within the framework of the engineering approach developed by Kumar, German and ... -
J-Integral Estimation Procedures
(The American Society of Mechanical Engineers (ASME), 1983)This paper presents efficient procedures for estimating the J -integral, a parameter for characterizing stable crack growth under inelastic conditions. Two different formulations are shown. The ... -
Parametric Representation of the Yield Strength-Strain Rate Behavior of A533B Steel
(The American Society of Mechanical Engineers (ASME), 1983)A nonlinear programming technique to estimate the parameters for a temperature normalized version of the Malvern equation is presented. The general conjugate gradient algorithm is used to minimize ... -
Errata: “Corrosion Fatique Crack Growth in Reactor Pressure Vessel Steels in PWR Primary Water” (Journal of Pressure Vessel Technology, 1983, 105, pp. 245–254) and “Development of Engineering Codes of Practice for Corrosion Fatigue” (Journal of Pressure Vessel Technology, 1983, 105, pp. 255–262)
(The American Society of Mechanical Engineers (ASME), 1983) -
An International Dialogue of Experiences in Elevated Temperature Design (PVP Special Publications, Vols. 60 and 66)
(The American Society of Mechanical Engineers (ASME), 1983) -
Free Vibration Analysis of Rectangular Plates
(The American Society of Mechanical Engineers (ASME), 1983) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1982) -
The Relationship Between Breach Development and the Depressurization Transient During Axial Rupture of a Gas-Pressurized Steel Pipe
(The American Society of Mechanical Engineers (ASME), 1982)Theoretical models are developed to predict the depressurization generated by a propagating axial rupture in a gas-pressurized steel pipe. The pressure transient is composed of a relatively slow ... -
Impacted Notch Bend Specimens
(The American Society of Mechanical Engineers (ASME), 1982)The proposed test procedure for instrumented impact testings is evaluated by the experimental and numerical dynamic fracture results obtained for Homalite-100, polycarbonate, A533B steel and 6061 ... -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1982) -
Residual Stress Generation and Relaxation in Butt-Welded Pipes
(The American Society of Mechanical Engineers (ASME), 1982)A numerical scheme for the determination of thermally induced local residual stresses and their relaxation behavior during heat treatment in the case of butt-welded pipes is described. The ... -
Collapse of Oil Well Casing
(The American Society of Mechanical Engineers (ASME), 1982)This paper is concerned with the theoretical study of the collapse of oil well casing under various loading conditions. The analysis is based on a model of a cylindrical shell of infinite ...