Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3761-3780 of 4506
-
Heat Conduction Through a Layered Pressure Vessel Wall
(The American Society of Mechanical Engineers (ASME), 1986)Heat conduction tests of a layered pressure vessel wall were performed using full-scale model pressure vessel courses. Thermal conductance between layers was estimated from the test results. A ... -
A Reference Stress Approach to the Steady Creep Deformation of Pipe Bends With End Constraints
(The American Society of Mechanical Engineers (ASME), 1986) -
Predictive Capabilities in Environmentally Assisted Cracking (Special Publication PVP-Vol. 99)
(The American Society of Mechanical Engineers (ASME), 1986) -
Structural Analysis and Design of Process Equipment
(The American Society of Mechanical Engineers (ASME), 1986) -
Letter to the Editor
(The American Society of Mechanical Engineers (ASME), 1986) -
A Review of Flow-Induced Vibration of Two Circular Cylinders in Crossflow
(The American Society of Mechanical Engineers (ASME), 1986)The flow field around a pair of rigid circular cylinders is very complex and has been studied extensively. When either one or both cylinders vibrate, the flow field becomes significantly more ... -
Analytical Simulation of Dynamically Equivalent Components
(The American Society of Mechanical Engineers (ASME), 1986)The inertia concept of modal mass was developed to provide a consistent methodology for establishing an analytically equivalent dynamic model of any discrete section within a complex piping ... -
Minimum Mass Design of Boiler Drums by Nonlinear Programming
(The American Society of Mechanical Engineers (ASME), 1985)Based on the systems approach to mathematical modeling, the paper shows the method for selecting the optimum design features of boiler drums with a given structure for minimum mass. The ... -
Weight and Cost Optimization of Hydrostatically Loaded Stiffened Flat Plates
(The American Society of Mechanical Engineers (ASME), 1985)Plates with longitudinal or orthogonal tee-stiffeners subjected to differential pressure are used in many structures. Equations to achieve minimum weight and cost are presented. Energy methods and ... -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1985) -
An Automatic Procedure for the Generation of Accelerograms Enveloping Several Design Response Spectra
(The American Society of Mechanical Engineers (ASME), 1985)During various steps in the design of a nuclear power plant, it is a common practice to generate accelerograms matching a design spectrum for one particular value of the damping ratio. Such ... -
Alternate Designs for Piping Integral Attachments
(The American Society of Mechanical Engineers (ASME), 1985)Axisymmetric discontinuity elastic analyses for two designs of piping integral attachments are presented. The proposed designs are partial and full penetration welded shear rings. The analytical ... -
Asymmetric Modes and Associated Eigenvalues for Spherical Shells
(The American Society of Mechanical Engineers (ASME), 1985)Free asymmetric vibration of spherical shells with clamped and hinged boundary conditions are analyzed using the finite element method. Element stiffness and consistent mass matrices are derived ... -
The Uniformly Valid Asymptotic Solution of Ellipsoidal Shell Heads in Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1985)In this paper, the complex equation is derived for the ellipsoidal shell heads in pressure vessels and uniformly valid asymptotic solution is given. -
Erratum: “Fatigue Crack Growth in Large Specimens With Various Stress Ratios” (Journal of Pressure Vessel Technology, 1984, 106, pp. 255–260)
(The American Society of Mechanical Engineers (ASME), 1985) -
Dynamics of Tubes in Fluid With Tube-Baffle Interaction
(The American Society of Mechanical Engineers (ASME), 1985)Three series of tests are performed to evaluate the effects of tube to tube-support-plate (TSP) clearance on tube dynamic characteristics and instability phenomena for tube arrays in crossflow. ... -
Study on Underclad Cracking in Nuclear Reactor Vessel Steels
(The American Society of Mechanical Engineers (ASME), 1985)Susceptibility to underclad cracking in nuclear reactor vessel steels, such as SA533 Grade B Class 1 and SA508 Class 2, was studied in detail. A convenient simulation test method using simulated ... -
Topics in Fluid Structure Interaction
(The American Society of Mechanical Engineers (ASME), 1985) -
The Impact of NDE Unreliability on Pressure Vessel Fracture Predictions
(The American Society of Mechanical Engineers (ASME), 1985)This paper reviews the significant variables of flaw depth, length, location and orientation required for fracture mechanics evaluations of pressure vessel integrity. Results of calculations emphasize ... -
Letter to the Editor commenting on “Letter to the Editor commenting on ‘Maximum Stresses and Flexibility Factors of Smooth Pipe Bends With Tangent Pipe Terminations Under In-Plane Bending’” (Whatham, J. F., 1984, ASME J. Pressure Vessel Technol., 106, pp. 219–220)
(The American Society of Mechanical Engineers (ASME), 1985)