Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 5901-5920 of 9564
-
Radiation and Convection Heat Transfer in a Porous Bed
(The American Society of Mechanical Engineers (ASME), 1968)The one-dimensional steady-state temperature distribution within an isotropic porous bed subjected to a collimated and/or diffuse radiation heat flux and a transparent flowing fluid has been ... -
A Mathematical Model For Steady Operation of Stirling-Type Engines
(The American Society of Mechanical Engineers (ASME), 1968)A mathematical model of Stirling-type engines has been developed. The complexity of the problem has been reduced by analyzing the various components of the engine (heat exchangers, regenerator, ... -
Sulfur Oxide Reactions: Radioactive Sulfur and Microprobe Studies of Corrosion and Deposits
(The American Society of Mechanical Engineers (ASME), 1968)The reactions of SO2 and SO3 with catalytic surfaces containing iron oxides, alone and in combination with various sodium salts, have been investigated. The SO3 concentration gradients above the ... -
A Research Study on Internal Corrosion of High-Pressure Boilers
(The American Society of Mechanical Engineers (ASME), 1968)The following report is the third and last in a series describing the progress of “A Research Study on Internal Corrosion of High Pressure Boilers.” The first report described the background, ... -
Effects of New International Formulation on Turbine-Generator Performance Calculations
(The American Society of Mechanical Engineers (ASME), 1968)For the pressure-temperature range of steam turbine operation the new International Formulation properties differ from those in Keenan and Keyes Steam Tables primarily in the values of enthalpy ... -
Low Cost Capacity For Peaking Generation
(The American Society of Mechanical Engineers (ASME), 1968)A means of obtaining peaking generation from existing generating units is proposed, by installing lower steam temperature boiler capacity in parallel with the existing boiler; the additional steam ... -
A High Strength Nickel-Base Alloy With Improved Oxidation Resistance up to 2200 deg F
(The American Society of Mechanical Engineers (ASME), 1968)A high strength nickel-base alloy has been developed which compares favorably in oxidation resistance with known high strength nickel-base alloys. The alloy, although basically a cast material, ... -
Discussion: “Effects of New International Formulation on Turbine-Generator Performance Calculations” (Cotton, K. C., Deming, N. R., and Garbinski, E. H., 1968, ASME J. Eng. Power, 90, pp. 15–20)
(The American Society of Mechanical Engineers (ASME), 1968) -
Performance Evaluation of Pumps in Air and Water
(The American Society of Mechanical Engineers (ASME), 1968)To explore the feasibility of establishing pump performance in air, two different designs were tested over the same range of shaft speed and flow rate in both water and air. The larger unit ... -
An Attempt to Generalize Similarity Considerations of Compressors and Pumps
(The American Society of Mechanical Engineers (ASME), 1968) -
Similarity in Centrifugal Compressors and Pumps
(The American Society of Mechanical Engineers (ASME), 1968) -
The Effects of Variations in Municipal Refuse on Some Incinerator Design Parameters
(The American Society of Mechanical Engineers (ASME), 1968)The variability of municipal refuse can have a marked effect on the performance of an incinerator during test, as compared to design expectations. A computer program has been developed which ... -
Testing Pumps as Fans and Fans as Pumps
(The American Society of Mechanical Engineers (ASME), 1968) -
Proposed ASME Performance Test Code for Nuclear Reactor Fuel
(The American Society of Mechanical Engineers (ASME), 1968)In the process of drafting a Performance Test Code for Nuclear Reactor Fuel, a question has arisen as to whether the present state of knowledge and experience will permit the writing of a ... -
A Laboratory Study of High-Temperature Corrosion on Fireside Surfaces of Coal-Fired Steam Generators
(The American Society of Mechanical Engineers (ASME), 1968)Three experimental approaches gave significant information on high-temperature fireside corrosion: 1 Sodium and potassium chlorides, injected through a gas flame, were deposited as such and then ... -
Measuring Abrasiveness of Solid Fuels and Other Materials by a Radiochemical Method
(The American Society of Mechanical Engineers (ASME), 1968)A new method for predicting pulverizer grinding element wear has been developed. This paper describes a laboratory model, ball-and-race, grinding machine, and a radioactive tracer technique used ... -
Shell Theory Solution for Asymmetric Balanced Radial Loads on Long Cylinders
(The American Society of Mechanical Engineers (ASME), 1968)The elastic behavior of a long cylinder subjected to equilibrated radial loads is considered. The problem is formulated by the use of shell theory equations. Although numerical results are ... -
Approximate Analysis of the Plastic Limit Pressures of Nozzles in Cylindrical Shells
(The American Society of Mechanical Engineers (ASME), 1968)An estimate of the limit pressure for cylindrical nozzles in cylindrical shells is derived from an upper bound analysis based on an assumed velocity distribution. The analysis is restricted to ... -
A Mathematical Model for Deposition From Turbulent Flows
(The American Society of Mechanical Engineers (ASME), 1968)A mathematical model was developed to estimate the dispersion and deposition of a contaminated flow. The model, which is independent of the nature of the contaminate source, is based on an ... -
Reynolds Number Effects in Axial Compressors
(The American Society of Mechanical Engineers (ASME), 1968)The influence of variations in flow Reynolds number on the performance of axial compressors has been studied (changes in Reynolds number being, for the most part, achieved by changes in the ...