Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 4681-4700 of 9564
-
FLOX® Combustion at High Power Density and High Flame Temperatures
(The American Society of Mechanical Engineers (ASME), 2010)In this contribution, an overview of the progress in the design of an enhanced FLOX® burner is given. A fuel flexible burner concept was developed to fulfill the requirements of modern ... -
Discussion: “An Analytical and Experimental Evaluation of the Pressure-Drop Losses in the Stirling Cycle” (Rios, P. A., and Smith, Jr., J. L., 1970, ASME J. Eng. Power, 92, pp. 182–187)
(The American Society of Mechanical Engineers (ASME), 1970) -
Chemistry of Additives and Contaminants in High Pressure Boilers
(The American Society of Mechanical Engineers (ASME), 1970) -
The Large Diesel Engine: Its Role in Automated Pipelines
(The American Society of Mechanical Engineers (ASME), 1970)The special requirements involved in the application of large diesel engines to automated pipeline service are covered in this paper. Further, these requirements are presented from three important ... -
Heat Transfer by a Square Array of Round Air Jets Impinging Perpendicular to a Flat Surface Including the Effect of Spent Air
(The American Society of Mechanical Engineers (ASME), 1970)The results of an experimental investigation on the average surface heat transfer co-efficients under a perforated plate of multiple, square array, round impinging air jets are presented. Correlation ... -
Unsteady Flow Phenomena in Rotating Centrifugal Impeller Passages
(The American Society of Mechanical Engineers (ASME), 1970)The phenomena of unsteady relative flow observed in a centrifugal impeller passage running at part capacity and zero flow are discussed. The mechanisms of passage stall for a shrouded and ... -
Flow Through Cascades of Slotted Compressor Blades
(The American Society of Mechanical Engineers (ASME), 1970)The performance of axial flow compressors can be improved when it becomes possible to achieve higher loading per stage than currently attainable. The major obstacles to attaining this objective ... -
Laminar Flow Gas Turbine Regenerators—The Influence of Manufacturing Tolerances
(The American Society of Mechanical Engineers (ASME), 1970)Several current designs for high effectiveness gas turbine regenerators involve low Reynolds number fully developed, laminar flow type surfaces. Such surfaces consist of cylindrical flow passages, ... -
Disposal of Wastes From Industrial Plants
(The American Society of Mechanical Engineers (ASME), 1970) -
Trials of Additives for Sulfur-Dioxide Removal in Industrial Plants
(The American Society of Mechanical Engineers (ASME), 1970)Trials of additives for the removal of sulfur dioxide from combustion gases have been made by several investigative groups. Three of these—an industry and local government cooperative group in ... -
Thermoeconomics and the Design of Heat Systems
(The American Society of Mechanical Engineers (ASME), 1970)This paper formulates the interactions between thermodynamics and economics for complex systems in a manner which assures a wise use of nonrenewable energy resources. The concept of “essergy” ... -
Application of the Thermoeconomic Approach to the Analysis and Optimization of a Vapor-Compression Desalting System
(The American Society of Mechanical Engineers (ASME), 1970)A conventional vapor-compression desalting system is analyzed thermodynamically and economically by the concepts of essergy and internal economy. Thermodynamic analysis using the concept of essergy ... -
Basic Factors in the Capture of Sulfur Dioxide by Limestone and Dolomite
(The American Society of Mechanical Engineers (ASME), 1970)The effectiveness of limestone and dolomite in removing SO2 from flue gas can be estimated by thermochemical calculations. Based on the most likely chemical reactions, both lime and magnesia ... -
Sulfur-Dioxide Removal From Power Plant Stack Gas by Limestone Injection: Plant-Scale Tests at TVA
(The American Society of Mechanical Engineers (ASME), 1970) -
Sulfur-Dioxide Removal From a Pilot Moving Grate Furnace Stack Gas
(The American Society of Mechanical Engineers (ASME), 1970)Peabody Coal Company, under contract to the National Center for Air Pollution Control, has investigated sulfur-dioxide removal from a pilot moving grate furnace stack gas by the addition of ... -
Discussion: “Heat Transfer by a Square Array of Round Air Jets Impinging Perpendicular to a Flat Surface Including the Effect of Spent Air” (Kercher, D. M., and Tabakoff, W., 1970, ASME J. Eng. Power, 92, pp. 73–82)
(The American Society of Mechanical Engineers (ASME), 1970) -
Discussion: “Unsteady Flow Phenomena in Rotating Centrifugal Impeller Passages” (Lennemann, E., and Howard, J. H. G., 1970, ASME J. Eng. Power, 92, pp. 65–71)
(The American Society of Mechanical Engineers (ASME), 1970) -
Discussion: “Basic Factors in the Capture of Sulfur Dioxide by Limestone and Dolomite” (Reid, William T., 1970, ASME J. Eng. Power, 92, pp. 11–15)
(The American Society of Mechanical Engineers (ASME), 1970) -
Some Experimental Results of Two Concepts Designed to Increase Turbine Blade Loading
(The American Society of Mechanical Engineers (ASME), 1970)A number of advanced blade concepts to efficiently increase turbine blade loading are being experimentally investigated. Tests made with a single-stage turbine rig have shown two of the advanced ... -
A Dynamic Model and Measurement Technique for Studying Induction Air Swirl in an Engine Cylinder
(The American Society of Mechanical Engineers (ASME), 1970)A dynamic engine model and measurement technique have been developed to study induction air swirl in the cylinder of a 4-stroke-cycle engine. Fabrication of the cylinder and piston crown of ...