Journal of Aerospace Engineering: Recent submissions
Now showing items 681-700 of 2488
-
Separated-Flow Control Simulation with a Periodic Excitation by SDBD Plasma Actuator at Re=O(205)
(ASCE, 11/1/2020 )This work presents a boundary layer separated-flow control technique with a periodic excitation by an single dielectric-barrier discharge (SDBD) plasma actuator applied to an airfoil section at Re=O(205). The technique ... -
Atomistic Simulation of Short Crack Growth in Correlation with Fatigue Indicator Parameter
(ASCE, 9/1/2020 1)Under time-varying extreme dynamic environmental conditions, fatigue damage could gradually accumulate with increased stress cycles at critical details of steel or other metallic structures. As a promising tool, a fatigue ... -
Stress-Level Buffeting Analysis and Wind Turbulence Intensity Effects on Fatigue Damage of Long-Span Bridges
(ASCE, 11/1/2020 )Buffeting-induced vibration, which has a frequent occurrence and relatively large amplitude, may cause fatigue damage to the steel girder of long-span bridges. Buffeting is caused by random wind turbulence, and the turbulence ... -
Influence of Local Delamination on Assembly Variation Modeling of Laminated Composite Beams
(ASCE, 9/1/2020 1)Laminated composite components have been widely used in engineering fields, such as aerospace engineering, automotive industries, marine structures, and civil infrastructure. Due to the inherent properties of laminated ... -
Multistage Liquid Rocket Weight Estimation and Optimization for Early Design Stages
(ASCE, 11/1/2020 )An improved method was proposed to estimate the structural ratios of a multistage liquid rocket for the early design stages, for example, the preliminary sizing analysis, or mission design level. The method computes the ... -
Aerothermodynamic Assessment of Spiked Configuration for Drag Reduction at Hypersonic Speeds
(ASCE, 11/1/2020 )Aerothermodynamic analysis was performed for blunt-body configurations with spikes mounted to determine drag reduction effectiveness. In-house perfect gas and chemical nonequilibrium solvers were utilized. The analysis ... -
Conversion Flight Control for Tilt Rotor Aircraft Using Nonlinear Time-Varying Perspective
(ASCE, 9/1/2020 1)Unlike the popularly used approaches (in which the time-varying nature of the system’s dynamics is neglected), a Lyapunov-based nonlinear time-varying framework is provided to handle the longitudinal control of tilt rotor ... -
Stability of a Tapered, Pretwisted, and Rotating Sandwich Beam under Temperature Gradient
(ASCE, 9/1/2020 1)In this work the parametric instability regions of an exponentially tapered, pretwisted, and rotating symmetric sandwich beam under a temperature gradient, subjected to a periodic axial load has been studied for clamped-free ... -
Assessment of Inverse Hyperbolic Zigzag Theory for Hygro-Thermomechanical Analysis of Laminated Composite and Sandwich Plates
(ASCE, 9/1/2020 1)In the present work, the hygro-thermomechanical response on the static characteristics of symmetric and antisymmetric laminated composite and sandwich plates is obtained using the recently developed inverse hyperbolic ... -
Effects of Wall Temperature on the Evolution of a Large-Amplitude Entropy Wave
(ASCE, 11/1/2020 )A high-order finite-difference scheme is employed to discretize the complete Navier-Stokes equations in order to simulate the hypersonic unsteady flowfield over a blunt cone. The hypersonic unsteady flowfield due to ... -
Numerical and Experimental Investigations on Windage Heating Effect of Labyrinth Seals
(ASCE, 9/1/2020 1)The heat load caused by windage heating effect of labyrinth seals seriously influences the sealing of shaft air flow. To reveal the windage heating effect of labyrinth seals to reasonably design an aeroengine rotor, this ... -
Aerodynamic Reduced-Order Model of Shape-Change Blade Subjected to Upstream Wake
(ASCE, 9/1/2020 1)This paper presents a Volterra series reduced-order model method to evaluate aerodynamic forces of aircraft engine blade designs, whose shape changes during design and are always excited by upstream wakes. The method uses ... -
Aeroelastic Stability and Nonlinear Flutter Analysis of Heated Panel with Temperature-Dependent Material Properties
(ASCE, 11/1/2020 )With the use of new structural materials and intelligent materials in aircraft panel manufacturing and flutter suppression, temperature-dependent material properties are increasingly outstanding. In this study, the effects ... -
Trajectory Prediction of a Model Rocket Falling into the Towing Tank: Experimental Tests versus Numerical Simulations
(ASCE, 9/1/2020 1)The SpaceX company has introduced a reusable first stage rocket that lands on a floating barge. In the event that the first stage rocket falls off the platform, the investigation of landing location on the seafloor may ... -
Application of LS-DYNA Constitutive Material Model Laws to Simulate Low Velocity Impact Damage to Composite Plates
(ASCE, 11/1/2020 )This paper presents the results of a comparative study conducted to assess the applicability and effectiveness of constitutive material model laws specific to composite materials contained in the LS-DYNA FE code. The LS-DYNA ... -
Performance Enhancement of a Supersonic Air Intake by Applying a Heat Source
(ASCE, 9/1/2020 1)The main objective of this paper is to study the effects of applying a heat source ahead of a supersonic mixed compression air intake. This intake has been designed for the freestream Mach number 2. Four parameters of the ... -
Theoretical and Numerical Analyses of Aerodynamic Characteristics on Shock Vector Control
(ASCE, 9/1/2020 1)A transverse injection into high-speed freestreams is a significant principle applied to realistic engineering applications, such as drag reduction, fuel service in a scramjet combustor, and fluidic thrust vectoring control. ... -
Physically Based Constitutive Model for Viscoplastic Deformation of Inconel718 at High Strain Rates and Temperatures
(ASCE, 9/1/2020 1)In the cutting process of nickel-based superalloys, because of the high strain rate and cutting temperature, the cutting deformation is complex and there exist hardening and softening phenomena. Therefore, the present study ... -
Novel Extreme Learning Machine Using Kalman Filter for Performance Prediction of Aircraft Engine in Dynamic Behavior
(ASCE, 9/1/2020 1)In this paper, a novel state-propagation extreme learning machine using a Kalman filter (KF-ELM) is proposed. In comparison with the plain extreme learning machine, the proposed algorithm takes the topological parameters ... -
Design of Supercritical Low-Reynolds-Number Airfoils for Fixed-Wing Flight on Mars
(ASCE, 9/1/2020 1)Aerodynamic shape optimization for the high-subsonic low-Reynolds-number flow regime represents an area of ongoing research. The interaction between supercritical compressible flow and laminar boundary layer separation is ...