YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Experimental Investigation by Speckle Interferometry of Solder Joint Failure Under Thermomechanical Load Aggravated by Boundary Conditions at Board Level

    Source: Journal of Electronic Packaging:;2012:;volume( 134 ):;issue: 004::page 41007
    Author:
    D. N. Borza
    ,
    I. T. Nistea
    DOI: 10.1115/1.4007812
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: Reliability of electronic assemblies at board level and solder joint integrity depend upon the stress applied to the assembly. The stress is often of thermomechanical or of vibrational nature. In both cases, the behavior of the assembly is strongly influenced by the mechanical boundary conditions created by the printed circuit board (PCB) to casing fasteners. In many previously published papers, the conditions imposed to the fasteners are mostly aiming at an increase of the fundamental frequency and a decrease of static or dynamic displacement values characterizing the deformation. These conditions aim at reducing the fatigue in different parts of these assemblies. In the photomechanics laboratory of INSA Rouen, the origins of solder joint failure have been investigated by means of full-field measurements of the flexure deformation induced by vibrations or by forced thermal convection. The measurements were done both at a global level for the whole printed circuit board assembly (PCBA) and at a local level at the solder joints where failure was reported. The experimental technique used was phase-stepped laser speckle interferometry. This technique has a submicrometer sensitivity with respect to out-of-plane deformations induced by bending and its use is completely nonintrusive. Some of the results were comforted by comparison with a numerical finite elements model. The experimental results are presented either as time-average holographic fringe patterns, as in the case of vibrations, or as wrapped phase patterns, as in the case of deformation under thermomechanical stress. Both types of fringe patterns may be processed so as to obtain the explicit out-of-plane static deformation (or vibration amplitude) maps. Experimental results show that the direct cause of solder joint failure may be a high local PCB curvature produced by a supplementary fastening screw intended to reduce displacements and increase fundamental frequency. The curvature is directly responsible for tensile stress appearing in the leads of a large quad flat pack (QFP) component and for shear in the corresponding solder joints. The general principle of increasing the fundamental frequency and decreasing the static or dynamic displacement values has to be checked against the consequences on the PCB curvature near large electronic devices having high stiffness.
    keyword(s): Deformation , Measurement , Interferometry , Screws , Stress , Diffraction patterns , Vibration , Boundary-value problems , Displacement , Failure , Solder joints , Printed circuit board assemblies , Reliability , Bending (Stress) , Manufacturing AND Fatigue ,
    • Download: (2.027Mb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Experimental Investigation by Speckle Interferometry of Solder Joint Failure Under Thermomechanical Load Aggravated by Boundary Conditions at Board Level

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/148566
    Collections
    • Journal of Electronic Packaging

    Show full item record

    contributor authorD. N. Borza
    contributor authorI. T. Nistea
    date accessioned2017-05-09T00:49:23Z
    date available2017-05-09T00:49:23Z
    date copyright41244
    date issued2012
    identifier issn1528-9044
    identifier otherJEPAE4-926513#ep_134_4_041007.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/148566
    description abstractReliability of electronic assemblies at board level and solder joint integrity depend upon the stress applied to the assembly. The stress is often of thermomechanical or of vibrational nature. In both cases, the behavior of the assembly is strongly influenced by the mechanical boundary conditions created by the printed circuit board (PCB) to casing fasteners. In many previously published papers, the conditions imposed to the fasteners are mostly aiming at an increase of the fundamental frequency and a decrease of static or dynamic displacement values characterizing the deformation. These conditions aim at reducing the fatigue in different parts of these assemblies. In the photomechanics laboratory of INSA Rouen, the origins of solder joint failure have been investigated by means of full-field measurements of the flexure deformation induced by vibrations or by forced thermal convection. The measurements were done both at a global level for the whole printed circuit board assembly (PCBA) and at a local level at the solder joints where failure was reported. The experimental technique used was phase-stepped laser speckle interferometry. This technique has a submicrometer sensitivity with respect to out-of-plane deformations induced by bending and its use is completely nonintrusive. Some of the results were comforted by comparison with a numerical finite elements model. The experimental results are presented either as time-average holographic fringe patterns, as in the case of vibrations, or as wrapped phase patterns, as in the case of deformation under thermomechanical stress. Both types of fringe patterns may be processed so as to obtain the explicit out-of-plane static deformation (or vibration amplitude) maps. Experimental results show that the direct cause of solder joint failure may be a high local PCB curvature produced by a supplementary fastening screw intended to reduce displacements and increase fundamental frequency. The curvature is directly responsible for tensile stress appearing in the leads of a large quad flat pack (QFP) component and for shear in the corresponding solder joints. The general principle of increasing the fundamental frequency and decreasing the static or dynamic displacement values has to be checked against the consequences on the PCB curvature near large electronic devices having high stiffness.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleExperimental Investigation by Speckle Interferometry of Solder Joint Failure Under Thermomechanical Load Aggravated by Boundary Conditions at Board Level
    typeJournal Paper
    journal volume134
    journal issue4
    journal titleJournal of Electronic Packaging
    identifier doi10.1115/1.4007812
    journal fristpage41007
    identifier eissn1043-7398
    keywordsDeformation
    keywordsMeasurement
    keywordsInterferometry
    keywordsScrews
    keywordsStress
    keywordsDiffraction patterns
    keywordsVibration
    keywordsBoundary-value problems
    keywordsDisplacement
    keywordsFailure
    keywordsSolder joints
    keywordsPrinted circuit board assemblies
    keywordsReliability
    keywordsBending (Stress)
    keywordsManufacturing AND Fatigue
    treeJournal of Electronic Packaging:;2012:;volume( 134 ):;issue: 004
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian