Constructal Design Applied to the Geometric Optimization of Y-shaped Cavities Embedded in a Conducting MediumSource: Journal of Electronic Packaging:;2011:;volume( 133 ):;issue: 004::page 41008DOI: 10.1115/1.4005296Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: In this paper, we rely on the Constructal method to optimize the geometry of a Y-shaped cavity embedded into a solid conducting wall. The structure has four degrees of freedom. The objective is to minimize the global thermal resistance between the solid and the cavity. The optimization procedure has demonstrated that for larger solids, a cavity shaped as T led to a minimization of the global thermal resistance, while the opposite effect is observed for tall solids, where the optimal shapes are reached when the bifurcated branches deeply penetrates the solid in the vertical direction, according to the Constructal principle of “optimal distribution of imperfections”. The three times minimized global thermal resistance of the Y-shaped cavity has been correlated by power laws as a function of its corresponding optimal configurations. Finally, the performance of the Y-shaped intrusion proved to be superior to that of other basic geometries: the optimized global thermal resistances of the Y-shaped cavities obtained for H/L = 1.0, 2.0, and 5.0 were, respectively 66.61%, 55.37%, and 19.05% lower than the optimal T-shaped cavities under the same thermal and geometric conditions. Furthermore, in comparison with the “finger cavity” shaped as C, the Y-shaped cavities increased the thermal performance in 109.12%, 84.45%, 59.32%, and 20.10% for H/L = 0.5, 1.0, 2.0, and 5.0, respectively.
keyword(s): Cavities , Geometry , Shapes , Thermal resistance , Design , Optimization , Degrees of freedom AND Bifurcation ,
|
Collections
Show full item record
| contributor author | G. Lorenzini | |
| contributor author | C. Biserni | |
| contributor author | L. A. Isoldi | |
| contributor author | L. A. O. Rocha | |
| contributor author | E. D. dos Santos | |
| date accessioned | 2017-05-09T00:43:06Z | |
| date available | 2017-05-09T00:43:06Z | |
| date copyright | December, 2011 | |
| date issued | 2011 | |
| identifier issn | 1528-9044 | |
| identifier other | JEPAE4-26319#041008_1.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/145770 | |
| description abstract | In this paper, we rely on the Constructal method to optimize the geometry of a Y-shaped cavity embedded into a solid conducting wall. The structure has four degrees of freedom. The objective is to minimize the global thermal resistance between the solid and the cavity. The optimization procedure has demonstrated that for larger solids, a cavity shaped as T led to a minimization of the global thermal resistance, while the opposite effect is observed for tall solids, where the optimal shapes are reached when the bifurcated branches deeply penetrates the solid in the vertical direction, according to the Constructal principle of “optimal distribution of imperfections”. The three times minimized global thermal resistance of the Y-shaped cavity has been correlated by power laws as a function of its corresponding optimal configurations. Finally, the performance of the Y-shaped intrusion proved to be superior to that of other basic geometries: the optimized global thermal resistances of the Y-shaped cavities obtained for H/L = 1.0, 2.0, and 5.0 were, respectively 66.61%, 55.37%, and 19.05% lower than the optimal T-shaped cavities under the same thermal and geometric conditions. Furthermore, in comparison with the “finger cavity” shaped as C, the Y-shaped cavities increased the thermal performance in 109.12%, 84.45%, 59.32%, and 20.10% for H/L = 0.5, 1.0, 2.0, and 5.0, respectively. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Constructal Design Applied to the Geometric Optimization of Y-shaped Cavities Embedded in a Conducting Medium | |
| type | Journal Paper | |
| journal volume | 133 | |
| journal issue | 4 | |
| journal title | Journal of Electronic Packaging | |
| identifier doi | 10.1115/1.4005296 | |
| journal fristpage | 41008 | |
| identifier eissn | 1043-7398 | |
| keywords | Cavities | |
| keywords | Geometry | |
| keywords | Shapes | |
| keywords | Thermal resistance | |
| keywords | Design | |
| keywords | Optimization | |
| keywords | Degrees of freedom AND Bifurcation | |
| tree | Journal of Electronic Packaging:;2011:;volume( 133 ):;issue: 004 | |
| contenttype | Fulltext |