Viscoelastic Properties of Ovine Adipose Tissue Covering the Gluteus MusclesSource: Journal of Biomechanical Engineering:;2007:;volume( 129 ):;issue: 006::page 924DOI: 10.1115/1.2800830Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: Pressure-related deep tissue injury (DTI) is a life-risking form of pressure ulcers threatening immobilized and neurologically impaired patients. In DTI, necrosis of muscle and enveloping adipose tissues occurs under intact skin, owing to prolonged compression by bony prominences. Modeling the process of DTI in the buttocks requires knowledge on viscoelastic mechanical properties of the white adipose tissue covering the gluteus muscles. However, this information is missing in the literature. Our major objectives in this study were therefore to (i) measure short-term (HS) and long-term (HL) aggregate moduli of adipose tissue covering the glutei of sheep, (ii) determine the effects of preconditioning on HS and HL, and (iii) determine the time course of stress relaxation in terms of the transient aggregate modulus H(t) in nonpreconditioned (NPC) and preconditioned (PC) tissues. We tested 20 fresh tissue specimens (from 20 mature animals) in vitro: 10 specimens in confined compression for obtaining the complete H(t) response to a ramp-and-hold protocol (ramp rate of 300mm∕s), and 10 other specimens in swift indentations for obtaining comparable short-term elastic moduli at higher ramp rates (2000mm∕s). We found that HS in confined compression were 28.9±14.9kPa and 18.1±6.9kPa for the NPC and PC specimens, respectively. The HL property, 10.3±4.2kPa, was not affected by preconditioning. The transient aggregate modulus H(t) always reached the plateau phase (less than 10% difference between H(t) and HL) within 2min, which is substantially shorter than the times for DTI onset reported in previous animal studies. The short-term elastic moduli at high indentation rates were 22.6±10kPa and 15.8±9.4kPa for the NPC and PC test conditions, respectively. Given a Poisson’s ratio of 0.495, comparison of short-term elastic moduli between the high and slow rate tests indicated a strong deformation-rate dependency. The most relevant property for modeling adipose tissue as related to DTI is found to be HL, which is conveniently unaffected by preconditioning. The mechanical characteristics of white adipose tissue provided herein are useful for analytical as well as numerical models of DTI, which are essential for understanding this serious malady.
keyword(s): Stress , Biological tissues , Compression , Muscle , Relaxation (Physics) , Cycles , Mechanical properties , Elastic moduli AND Modeling ,
|
Collections
Show full item record
| contributor author | Amit Gefen | |
| contributor author | Einat Haberman | |
| date accessioned | 2017-05-09T00:22:41Z | |
| date available | 2017-05-09T00:22:41Z | |
| date copyright | December, 2007 | |
| date issued | 2007 | |
| identifier issn | 0148-0731 | |
| identifier other | JBENDY-26773#924_1.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/135202 | |
| description abstract | Pressure-related deep tissue injury (DTI) is a life-risking form of pressure ulcers threatening immobilized and neurologically impaired patients. In DTI, necrosis of muscle and enveloping adipose tissues occurs under intact skin, owing to prolonged compression by bony prominences. Modeling the process of DTI in the buttocks requires knowledge on viscoelastic mechanical properties of the white adipose tissue covering the gluteus muscles. However, this information is missing in the literature. Our major objectives in this study were therefore to (i) measure short-term (HS) and long-term (HL) aggregate moduli of adipose tissue covering the glutei of sheep, (ii) determine the effects of preconditioning on HS and HL, and (iii) determine the time course of stress relaxation in terms of the transient aggregate modulus H(t) in nonpreconditioned (NPC) and preconditioned (PC) tissues. We tested 20 fresh tissue specimens (from 20 mature animals) in vitro: 10 specimens in confined compression for obtaining the complete H(t) response to a ramp-and-hold protocol (ramp rate of 300mm∕s), and 10 other specimens in swift indentations for obtaining comparable short-term elastic moduli at higher ramp rates (2000mm∕s). We found that HS in confined compression were 28.9±14.9kPa and 18.1±6.9kPa for the NPC and PC specimens, respectively. The HL property, 10.3±4.2kPa, was not affected by preconditioning. The transient aggregate modulus H(t) always reached the plateau phase (less than 10% difference between H(t) and HL) within 2min, which is substantially shorter than the times for DTI onset reported in previous animal studies. The short-term elastic moduli at high indentation rates were 22.6±10kPa and 15.8±9.4kPa for the NPC and PC test conditions, respectively. Given a Poisson’s ratio of 0.495, comparison of short-term elastic moduli between the high and slow rate tests indicated a strong deformation-rate dependency. The most relevant property for modeling adipose tissue as related to DTI is found to be HL, which is conveniently unaffected by preconditioning. The mechanical characteristics of white adipose tissue provided herein are useful for analytical as well as numerical models of DTI, which are essential for understanding this serious malady. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Viscoelastic Properties of Ovine Adipose Tissue Covering the Gluteus Muscles | |
| type | Journal Paper | |
| journal volume | 129 | |
| journal issue | 6 | |
| journal title | Journal of Biomechanical Engineering | |
| identifier doi | 10.1115/1.2800830 | |
| journal fristpage | 924 | |
| journal lastpage | 930 | |
| identifier eissn | 1528-8951 | |
| keywords | Stress | |
| keywords | Biological tissues | |
| keywords | Compression | |
| keywords | Muscle | |
| keywords | Relaxation (Physics) | |
| keywords | Cycles | |
| keywords | Mechanical properties | |
| keywords | Elastic moduli AND Modeling | |
| tree | Journal of Biomechanical Engineering:;2007:;volume( 129 ):;issue: 006 | |
| contenttype | Fulltext |