Error Analysis on Finite Element Modeling of Involute Spur GearsSource: Journal of Mechanical Design:;2006:;volume( 128 ):;issue: 001::page 90DOI: 10.1115/1.2114891Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: Finite element analysis can incorporate two-dimensional (2D) modeling if the geometry, load, and boundary conditions meet the requirements. For many applications, a wide range of problems are solved in 2D, due to the efficiency and costs of computation. However, care has to be taken to avoid modeling errors from significantly influencing the result. When the application area is nonlinear, such as when modeling contact problems or fracture analysis, etc, the 2D assumption must be used cautiously. In this paper, a large number of 2D and three-dimensional (3D) gear models were investigated using finite element analysis. The models included contact analysis between teeth in mesh, a gear body (disk), and teeth with and without a crack at the tooth root. The model results were compared using parameters such as the torsional (mesh) stiffness, tooth stresses and the stress intensity factors that are obtained under assumptions of plane stress, plane strain, and 3D analysis. The models considered variations of face width of the gear from 5 mm to 300 mm. This research shows that caution must be used especially where 2D assumptions are used in the modeling of solid gears.
keyword(s): Stress , Gears , Errors , Finite element analysis , Modeling , Stiffness , Fracture (Process) AND Plane strain ,
|
Collections
Show full item record
| contributor author | Jian D. Wang | |
| contributor author | Ian M. Howard | |
| date accessioned | 2017-05-09T00:21:08Z | |
| date available | 2017-05-09T00:21:08Z | |
| date copyright | January, 2006 | |
| date issued | 2006 | |
| identifier issn | 1050-0472 | |
| identifier other | JMDEDB-27819#90_1.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/134379 | |
| description abstract | Finite element analysis can incorporate two-dimensional (2D) modeling if the geometry, load, and boundary conditions meet the requirements. For many applications, a wide range of problems are solved in 2D, due to the efficiency and costs of computation. However, care has to be taken to avoid modeling errors from significantly influencing the result. When the application area is nonlinear, such as when modeling contact problems or fracture analysis, etc, the 2D assumption must be used cautiously. In this paper, a large number of 2D and three-dimensional (3D) gear models were investigated using finite element analysis. The models included contact analysis between teeth in mesh, a gear body (disk), and teeth with and without a crack at the tooth root. The model results were compared using parameters such as the torsional (mesh) stiffness, tooth stresses and the stress intensity factors that are obtained under assumptions of plane stress, plane strain, and 3D analysis. The models considered variations of face width of the gear from 5 mm to 300 mm. This research shows that caution must be used especially where 2D assumptions are used in the modeling of solid gears. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Error Analysis on Finite Element Modeling of Involute Spur Gears | |
| type | Journal Paper | |
| journal volume | 128 | |
| journal issue | 1 | |
| journal title | Journal of Mechanical Design | |
| identifier doi | 10.1115/1.2114891 | |
| journal fristpage | 90 | |
| journal lastpage | 97 | |
| identifier eissn | 1528-9001 | |
| keywords | Stress | |
| keywords | Gears | |
| keywords | Errors | |
| keywords | Finite element analysis | |
| keywords | Modeling | |
| keywords | Stiffness | |
| keywords | Fracture (Process) AND Plane strain | |
| tree | Journal of Mechanical Design:;2006:;volume( 128 ):;issue: 001 | |
| contenttype | Fulltext |