Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3081-3100 of 3257
-
Erosion of 310 Stainless Steel at 975°C in Combustion Gas Atmospheres
(The American Society of Mechanical Engineers (ASME), 1977)Erosion tests were conducted on 310 stainless steel in combustion gas atmospheres at 975°C. SiC particles of 100 mesh (150 μm) size were employed over a velocity range of 15–70 m/s at ... -
Erosion of a Tube by Gas-Particle Flow
(The American Society of Mechanical Engineers (ASME), 1977)A numerical model for particle-laden flow in a tube has been developed which predicts the erosive wear of the tube wall by the action of the impinging particles. Empirical relationships are ... -
Discussion: “Finite Element Solutions of Crack-Tip Behavior in Small Scale Yielding” (Tracey, D. M., 1976, ASME J. Eng. Mater. Technol., 98, pp. 146–151)
(The American Society of Mechanical Engineers (ASME), 1977) -
The Interplay of Geometric and Materials Variables in Energy Absorption
(The American Society of Mechanical Engineers (ASME), 1977)The specific energy absorbed during uniaxial tension and during axial compression of cylindrical tubes with various wall thicknesses and diameters has been measured for 1015 steel in two heat ... -
Effects of Surface Hardness and Other Material Properties on Erosive Wear of Metals by Solid Particles
(The American Society of Mechanical Engineers (ASME), 1977)Erosion of a material from a metal surface by the action of impinging SiC particles is studied. In a brief review, it is shown that investigators have correlated erosion wear with several ... -
Parameters Affecting the Velocity of Particles in an Abrasive Jet
(The American Society of Mechanical Engineers (ASME), 1977)Silicon carbide particles, mesh 60, were introduced at a known time-rate (wp ) into an air stream flowing at a time-rate (wa ) through a parallel sided nozzle of circular cross-section. ... -
Static and Dynamic Stress Intensity Factors by the Method of Transmitted Caustics
(The American Society of Mechanical Engineers (ASME), 1977)The stress intensity factors in plexiglas plates containing an edge crack and subjected to static or dynamic loading are determined by the optical method of caustics. Measurements of the applied ... -
Particle Erosion Measurements on Metals
(The American Society of Mechanical Engineers (ASME), 1977)A method being used to measure the erosive wear of metals at different temperatures and under controlled environmental conditions is described. A commercial apparatus has been modified that can ... -
Discussion: “The Modeling of Flow Concentration in Two-Phase Materials” (Cook, T. S., Rau, C. A., and Smith, E., 1976, ASME J. Eng. Mater. Technol., 98, pp. 180–189)
(The American Society of Mechanical Engineers (ASME), 1977) -
X-Ray Diffraction Study of Low Cycle Fatigue Damage in Plain Carbon Steel
(The American Society of Mechanical Engineers (ASME), 1977)An X-Ray diffraction analysis of low cycle bending fatigue was conducted on plain carbon steel (SAE 1008) in three conditions, as received (annealed) 20 percent prestrained, and strain aged. ... -
Effect of Hydrothermal Environments on the Erosion of Castable Refractories
(The American Society of Mechanical Engineers (ASME), 1977)Hydrothermal environments are expected to adversely affect the erosive resistance of castable refractories intended for use in high wear areas of coal gasification plants. The erosive wear behavior ... -
Erosive Effects of High Pressure and High Temperature Gases on Steel
(The American Society of Mechanical Engineers (ASME), 1977)An experimental study is being conducted to determine the thermochemical mechanisms by which short duration pulses (1 to 2 ms) of high pressure and temperature gases erode steel. A ballistic ... -
Overload Effects on Fatigue Damage of Wire-Rope Pendants
(The American Society of Mechanical Engineers (ASME), 1977) -
Low Level Charpy Impact Response of Graphite/Epoxy Hybrid Composites
(The American Society of Mechanical Engineers (ASME), 1977)Laminated graphite/epoxy composites, with and without the addition of plies of glass fabric/epoxy or unidirectional glass yarn/epoxy, were subjected to impact levels less than those necessary to ... -
Low-Cycle Fatigue Under Out-of-Phase Loading Conditions
(The American Society of Mechanical Engineers (ASME), 1977)A number of tests have been conducted on a 1 percent Cr-Mo-V steel under combined cyclic axial and torsional loads with various phase relationships. It is shown that endurance and the direction ... -
Corrosion Performance of Austenitic Alloys in Automobile Exhaust Environments
(The American Society of Mechanical Engineers (ASME), 1977)The performance of several austenitic alloys ranging from low alloy content stainless steels to nickel-base alloys has been evaluated at temperatures from 704–1093°C (1300–2000°F) in ... -
A Modified Tension Test
(The American Society of Mechanical Engineers (ASME), 1977)The present paper deals with a modified tension test with experimental results for SAE 1020, SAE 1215, and OFHC Cu of standard 12.8 mm (0.505 in.) dia test bars. The tension test was ... -
Dynamic Model of Expanded Polyethylene for Package Cushion Applications
(The American Society of Mechanical Engineers (ASME), 1977) -
An Improved Method for Numerical Integration of Constitutive Equations of the Work Hardening-Recovery Type
(The American Society of Mechanical Engineers (ASME), 1977) -
A Dynamic Optical Correlation Technique For Fatigue Failure Prediction
(The American Society of Mechanical Engineers (ASME), 1977)A continuous optical correlation technique for fatigue damage detection and fatigue failure prediction in metals is described. Information about the metal surface is recorded on a thermoplastic- ...