Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3061-3080 of 3257
-
Influence of Interstage Annealing on the Stretch-Formability of Sheet-Metal Laminates
(The American Society of Mechanical Engineers (ASME), 1977)The interstage annealing of sheet-metal laminates is studied. A method of predicting the stretch-formability, as measured by the maximum possible uniform strain in simple tension, is proposed. ... -
A Mechanical Equation of State for Inelastic Deformation of Iron: An Analytic Description
(The American Society of Mechanical Engineers (ASME), 1977)The applicability of two familiar analytic descriptions of micromechanical deformation as equations of state for polycrystalline iron is discussed. These equations are the power law and the ... -
Continuous Extrusion by Viscous Drag
(The American Society of Mechanical Engineers (ASME), 1977)A multistage continuous extrusion process based on a new concept is described and studied. The billet is driven through a series of dies by the viscous drag of a fluid flowing along its ... -
High Temperature Thermal-Elastic Analysis of Dissimilar Metal Transition Joints
(The American Society of Mechanical Engineers (ASME), 1977)Thermal-elastic analyses of dissimilar metal transition weld joints of a 24″ sodium piping system were performed. This piping system is for Liquid Metal Fast Breeder Reactor application, operating ... -
The Effect of Strain Rate Upon the Bending Behavior of Materials
(The American Society of Mechanical Engineers (ASME), 1977)The maximum loads sustainable in both four-point bending and prebent hinge collapse tests of several materials have been determined at crosshead rates from 4.2 × 10−3 mm/s to 4.2 m/s (10−2 ... -
The Fracture Toughness of Cast High-Strength Steels
(The American Society of Mechanical Engineers (ASME), 1977)The mechanical properties of four cast high-strength steels, 4340, 15-5 PII stainless steel, and two maraging steels were examined. To provide a direct comparison with wrought steels split heats ... -
Microstructural Effects in the Low-Cycle Fatigue of Fe-Ni-Cr Austenite
(The American Society of Mechanical Engineers (ASME), 1977)A series of low-cycle fatigue tests was performed at 593 deg C on Fe-20 Cr-10 Ni and Fe-20 Cr-20 Ni (in weight percent) austenitic alloys in both the cast and wrought conditions. The as-cast ... -
The Use of Classification Zones for Fatigue Behavior in Steels
(The American Society of Mechanical Engineers (ASME), 1977)Numerous studies on fatigue damage and fatigue crack propagation in the past dealt with these problems, either by a cumulative damage approach, or using crack propagation equations based on ... -
A Fracture Criterion for Porous Materials and Its Application to the Shape of Sintered Preforms in Forging
(The American Society of Mechanical Engineers (ASME), 1977)Ductile fracture of porous metals during forging was studied. The effect of the shape of sintered copper preforms on the forming limit is examined in upsetting with flat dies at room temperature. ... -
Creep Deformation of 20 Percent Cold Worked Type 316 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1977)Creep deformation of internally pressurized tube specimens of 20 percent cold worked Type 316 stainless steel was measured under isothermal, constant stress conditions. Stress levels varied from ... -
Creep and Rupture Behavior of Weld-Deposited Type 16-8-2 Stainless Steel at 593°C
(The American Society of Mechanical Engineers (ASME), 1977)The creep and rupture behavior of weld-deposited Type 16-8-2 stainless steel at 593°C was investigated over the time range from 3.6 × 104 s to 2.5 × 107 s. Equations relating ... -
Materials Division Best Paper Award: T. Muraki, J. J. Bryan, and K. Masubuchi
(The American Society of Mechanical Engineers (ASME), 1977) -
ASME Nadai Award: Evan A. Davis
(The American Society of Mechanical Engineers (ASME), 1977) -
Continuum Theory of Ductile Rupture by Void Nucleation and Growth: Part I—Yield Criteria and Flow Rules for Porous Ductile Media
(The American Society of Mechanical Engineers (ASME), 1977)Widely used constitutive laws for engineering materials assume plastic incompressibility, and no effect on yield of the hydrostatic component of stress. However, void nucleation and growth (and ... -
Fatigue of Metals as Stochastic Phenomena
(The American Society of Mechanical Engineers (ASME), 1977)A stochastic model for the fatigue of metals under repeated stress or strain is proposed. Fatigue lives up to crack initiation are investigated with the aid of a recent theory on a cumulative ... -
Temperature Dependences of the Elastic Constants of Precipitation-Hardened Aluminum Alloys 2014 and 2219
(The American Society of Mechanical Engineers (ASME), 1977)Elastic properties of precipitation-hardened aluminum alloys 2014 and 2219 were studied between 4 and 300 K using ultrasonic pulse techniques. Both the longitudinal and transverse sound velocities ... -
The Tensile Ductility of Austenitic Steels in Air and Hydrogen
(The American Society of Mechanical Engineers (ASME), 1977)An empirical correlation of yield strength with reduction-in-area at fracture was demonstrated for austenitic stainless steel. The correlation is consistent with an existing fracture model that ... -
Deformation and Fracture Mechanics of Engineering Materials
(The American Society of Mechanical Engineers (ASME), 1977) -
A J-Integral Approach to Crack Resistance for Aluminum, Steel, and Titanium Alloys
(The American Society of Mechanical Engineers (ASME), 1977)Crack growth resistance data have been obtained for a variety of materials as a function of thickness and crack orientation. Resistance to crack extension is determined in terms of the square ... -
Composite Structures of Steel and Concrete, Vol. 1
(The American Society of Mechanical Engineers (ASME), 1977)