Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2761-2780 of 3257
-
Lack of Hardening in Drawn Bars of Copper and Aluminum in Tension Tests
(The American Society of Mechanical Engineers (ASME), 1982)Oxygen-free copper, 6061 aluminum, and 1100 aluminum bars were drawn from various initial diameters in the annealed state to bars of 11.8 mm (0.464 in.) at maximum reductions in area up to ... -
Tensile Property Improvements of Spinodal Cu-15Ni-8Sn by Two-Phase Heat Treatment
(The American Society of Mechanical Engineers (ASME), 1982)A heat treatment has been developed which produces significant improvements in the tensile properties of Cu-15Ni-8Sn spinodal alloy. The treatment involves solution heat treatment in the two-phase ... -
High-Strain Multiaxial Fatigue
(The American Society of Mechanical Engineers (ASME), 1982)The aim of this investigation was to develop a method for the prediction of the high-strain multiaxial fatigue life (low-cycle fatigue) of a steel, based on high-strain uniaxial fatigue data. ... -
The Use of Notched Beams to Establish a Multiaxial Stress-Fracture Criterion for Beryllium
(The American Society of Mechanical Engineers (ASME), 1982)Fracture of beryllium under biaxial states of stress has been studied in the past using thin-walled tubes loaded by combinations of axial load, torsion, and internal pressure. In the present ... -
A Comparison of J Estimating Procedures for a Solid Subjected to Bending Loads
(The American Society of Mechanical Engineers (ASME), 1982)Zahoor and Kanninen have recently developed a simple procedure for estimating the magnitude of the J-integral for through-wall cracks in pipes subjected to bending loads. This paper gives ... -
The Minimum Elastic Energy Density Criterion in Dynamic Problems of Propagating Cracks
(The American Society of Mechanical Engineers (ASME), 1982)In a previous paper by the authors the minimum elastic strain energy density criterion was studied by considering the general case where both KI and KII -components of the stress intensity ... -
Fatigue of Small Helical Extension Springs Subjected to Static Torsion and Alternating Lateral Deflection
(The American Society of Mechanical Engineers (ASME), 1982)Multiaxial fatigue studies of peened helical extension springs made of music wire were performed in a specially designed testing machine. The test regime imposed static torsion and alternating ... -
Fatigue of Thick Tubes: Effect of Mean Pressure, Honing, Plating, Burnishing, and Peening
(The American Society of Mechanical Engineers (ASME), 1982)Experimental results are presented for fatigue of closed-ended thick-walled tubes of 2.5 wall ratio and 32.3 mm (1.27 in.) ID for SAE 4333 steel subjected to pulsating internal pressure. Results ... -
Stress-Strain Behavior of Inconel 718 During Low Cycle Fatigue
(The American Society of Mechanical Engineers (ASME), 1982)In the development of better methods of assessing damage accumulation, one of the requirements is an understanding of the cyclic constitutive behavior of the material. It is known that the ... -
Fatigue Crack Propagation Beyond General Yield
(The American Society of Mechanical Engineers (ASME), 1982)Tests are carried out on compact tension specimens of AISI 1020 hot-rolled steel at nominal stress levels beyond yield. The results show that crack propagation rates can be correlated successfully ... -
Evaluation of Creep Constitutive Equations for Type 304 Stainless Steel Under Repeated Multiaxial Loading
(The American Society of Mechanical Engineers (ASME), 1982)Four kinds of creep constitutive models, i.e., strain-hardening, modified strain-hardening, kinematic-hardening, and mixed-hardening theory, are evaluated on the basis of creep-test results on type ... -
The Effects of Induction Heating Conditions on Controlling Residual Stresses in Welded Pipes
(The American Society of Mechanical Engineers (ASME), 1982)Induction heating for stress improvement (IHSI) is a method for reducing the tensile weld induced stresses on the inner surfaces of the girth welded pipes. The process entails inductively heating ... -
Analysis of Test System Misalignment in the Creep Test
(The American Society of Mechanical Engineers (ASME), 1982)An analysis of test system misalignment is presented for the creep test. Sheet type rectangular 1100-0 aluminum specimens are used for discussion. It is found that the creep strain at the ... -
The Effect of Specimen Size on Stress-Strain Behavior in Compression
(The American Society of Mechanical Engineers (ASME), 1982)Compressions tests on right, cylindrical steel specimens were performed in order to determine the stress-strain behavior. Lubrication was achieved by using a thin PTFE (Hostaflon) sheet on either ... -
The Effect of Test System Misalignment in the Dynamic Tension Test
(The American Society of Mechanical Engineers (ASME), 1982)An analysis of test system misalignment is presented for dynamic tension test. Sheet type rectangular 1100-0 aluminum specimens are used for discussion. For a constant strain rate tension test, ... -
Multiaxial Stress Rupture Testing and Compendium of Data for Creep Resisting Steels
(The American Society of Mechanical Engineers (ASME), 1982)Recently, there has been an increasing need for more accurate methods of predicting the life of components operating in the creep range. Although many such components are invariably subject to ... -
Microstructural and Macrostructural Modeling of the Fracture Behavior of Pearlitic Gray Irons
(The American Society of Mechanical Engineers (ASME), 1982)An attempt is made to rationalize the fracture behavior of pearlitic gray irons on both the microstructural and macrostructural levels. Along with the effects of inoculation, those of as-cast ... -
Ternary Equilibrium Diagrams (Second Edition)
(The American Society of Mechanical Engineers (ASME), 1982) -
Further Compositional Effects on the Temper Embrittlement of 2 1/4 Cr-1 Mo Steels
(The American Society of Mechanical Engineers (ASME), 1982)As an extension of a previous study (reference [1]), the effects of a 0.3 pct nickel content, of tin in combination with several other elements, and of a 0.1 pct vs a 0.2 pct carbon ... -
Introduction to Polymers
(The American Society of Mechanical Engineers (ASME), 1982)